strike (B) and replace screw. Undo screw (J) and remove buffer. Remove screws (C) and latch 3 plate (D). Remove hinge block screw (E). Remove door from hinge blocks.
Remove hinge screws (F) and hinge (G) and refit to opposite side as shown.
INSTRUCTIONS FOR USE
Refit latch plate (D) with screws (C). Remove screw (H) at top of door and re fit switch strike (B) as shown. Refit buffer (J). Fit door to hinge blocks and secure with screws (E)
Large Door Opening :B
First remove the child safety peg from the top of the door by rotating 90� anticlockwise. Now unscrew the door hinges from the machine by removing the 4 screws. Do not use a power screwdriver as this may damage the screw threads.
J
D
Remove the four screws from the opposite side of the door opening. Place these screws in the hinge holes on the other side of the door J hinge screws.
C
E
J
Reverse door and fit to dryer inopening. screw (E) to(C). Remove Refit latch plate (D) with screws secure hinge cover. Fit closed position. Refit(H) at top of door andscrewandat top of door screw screws (G) Reverse the doorfit(H) re apply the Remove re switch strike and hinge cover (F). Open the door. and refit switch strike (B) as shown.
remove switch Pull the hinge cover (F) forwards to Open G do screw switchthe door. Undoreplace(A) remove (J) and (B) and screw screw.F strike Undo remove it. Remove two outer (C) and latch (J) and remove buffer. Remove screws (G). Remove door. Fit latch screw Remove hinge crew (E). screws (C) and latch plate (D). Remove screws(D) with screws (C) (G) plate (F) and hinge and refit to opposite side as shown. . hinge cover screw (E). Close the door.
B A
(B) as shown. Replace the(J). (J).safe peg in the top of the, now reversed, door. Refit bufferbuffer Fit door to Refit child hinge blocks and secure with screws (E)
Dryers fitted Large Door Opening :- without hinge cover :-
DSG RetailHLtd.Bis responsible for after sales service and any claims in respect of this licensed product. If you have a query about the product please contact our Currys product support line (08701) 565550
1 2 3 First remove the child safety peg from the top of the door by rotating 90� anticlockwise. Now unscrew the door hinges from the machine by removing the 4 screws. Do not use a power screwdriver as this may damage the screw threads. Remove the four screws from the opposite side of the door opening. Place these screws in the hinge holes on the other side of the door opening. Reverse the door and re apply the hinge screws. Replace the child safe peg in the top of the, now reversed, door. J
E C D D C E J
Open the door. Undo screw (A) remove switch DSG Retail Ltd. screw. Undo screw after sales service andFany claims in respect of this licensed product. latch plate (D) with screws (C). Remove Refit strike (B) and replaceis responsible for (J) and G screw (H) at top of door and re fit switch strike remove buffer. Remove screws (C) and latch please contact our Currys product support line (08701) 565550 If you have a query about the product Remove hinge screws (F) and hinge (G) (B) as shown. Refit buffer (J). Fit door to plate (D). Remove hinge block screw (E). and refit to opposite side as shown. hinge blocks and secure with screws (E) Remove door from hinge blocks.
First remove the child safety peg from the top of the door by rotating 90� anticlockwise. Now unscrew the door hinges from the machine by removing the 4 screws. Do not use a power screwdriver as this may damage the screw threads. Remove the four screws from the opposite side of the door opening. Place these screws in the hinge holes on the other side of the door opening. Reverse the door and re apply the hinge screws. Replace the child safe peg in the top of the, now reversed, door.
DSG Retail Ltd. is responsible for after sales service and any claims in respect of this licensed product. If you have a query about the product please contact our Currys product support line (08701) 565550
�
�
�
�
�
�
�
�
�
�
�
and the condenser every three or four months or the restrictions to airflow will extend drying times and could cause the safety cut-out to trip. Under no circumstances should anything other than the recommended articles be placed in the tumble dryer. The tumble dryer should be serviced by an appointed service organisation and only genuine parts used. It is dangerous to alter or modify the product in any way other than fitting authorised accessories. We recommend that the appliance is unplugged each time after use. It should always be disconnected from the electricity supply if it is to be left unattended for long periods (i.e. weekends, holidays etc.)
Do not stack the tumble dryer on top of other appliances without the correct stacking kit. Any electrical work required to install the appliance should be carried out by a qualified person. It is important to clean the lint filter after each drying cycle
The rear of the dryer gets quite hot during use. Position the dryer so that the back is not accessible while in operation.
Please note it is not recommended that the dryer is placed directly next to ovens or cookers as the performance of the dryer may be affected. A carpet must not obstruct the ventilation openings in the base of the dryer.
This tumble dryer is intended for NORMAL DOMESTIC USE ONLY.
These notes are provided in the interest of safety. You must read them before installing or using the appliance.
IMPORTANT USER INFORMATION
�
�
� � �
�
�
�
�
CAUTION HOT SURFACE
to do so could result in water leaking. DO NOT use a two-way adaptor, or extension lead. The dryer must be connected to its own socket. DO NOT block the air inlets at the front and back of your dryer.
It is important to clean fluff from the window of the dryer and around the door seal after each drying cycle. Failure
damaged in any way. Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause serious injury. Consult your local appointed service engineer and insist on genuine spare parts. If the mains cord is damaged it must be replaced by a special cord available from the manufacturer or its service agent
DO NOT place articles in the dryer if anything other than a water solution has been used in the cleaning process.
DO NOT attempt to dry dripping wet articles or items containing foam rubber or rubber-like materials. DO NOT use the tumble dryer if you suspect that it is
DO NOT allow fluff to accumulate around the tumble dryer. DO NOT exceed the recommended maximum load. DO NOT allow children to tamper with the controls and keep them away from the dryer when it is in operation.
THIS APPLIANCE MUST BE EARTHED
This label, positioned on the rear of your dryer, indicates the surface is hot when in operation - avoid touching
�
�
�
RE-INSTALLING THE CONDENSER
�
REMOVING THE CONDENSER
NOTE: The condenser will discolour through use.
or more frequently if the dryer is in constant use. See �CLEANING THE CONDENSER� opposite.
The condenser and ducting should be cleaned 3 or 4 times a year
before closing or water may leak. IMPORTANT: The dryer may leak if the condenser is not correctly re-installed.
Carefully push the condenser back into the machine, until it is pushed fully home and a �click� is heard. Ensure all lint and fluff is removed from around the grille seal
Firmly pull the condenser out.
THE CONDENSER1
�
�
�
�
CAUTION: For maximum efficiency, the plates are made from very thin aluminium and are easily damaged. Do not try to poke 2 anything between the plates or use a hard object or tool for cleaning. At all times, handle the condenser carefully and avoid crushing the plates.
CLEANING THE CONDENSER 1
After cleaning, re-install the condenser (see opposite).
Whilst the condenser is removed, clean as much fluff as possible from inside the ducting by reaching a hand into the machine. In particular, keep the passage from the fan clear (on the right hand side of the condenser duct). 2
and carefully shake off excess water.
Flush the fluff from between the plates under running water
Remove the condenser (see opposite).
2
2
2
1
2 1
Large Door Opening :-
1
2
1 2
GB
4213 094 93702
IMPORTANT: PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS APPLIANCE. KEEP THEM IN A SAFE PLACE FOR FUTURE REFERENCE.
