SONY KD32DX40U
Instrukcja Serwisowa

The operating instructions mentioned here are partial abstracts from the �Operating Instruction Manual�. The page numbers of the �Operating Instruction Manual� remain as in the manual.
Getting Started Basic Operation

5. Automatically tuning the TV
1. When you switch on the TV for the first time a menu appears on the screen asking you to check if the picture is slanted. (Sometimes the Earth�s natural magnetism can cause the screen to look tilted.)
VIDEO

Selecting Digital or analogue mode
Press the DIGITAL/
Checking the picture tilt.

button on the remote control to switch between Digital and analogue mode. To

check if you are watching a Digital or analogue mode press the PROG +/- button. If you are watching a digital programme a banner will appear momentarily at the top of the screen.

/

TV

/

The Programme Index table
a) If no correction is required, press the V or v buttons on the
If picture slants, please adjust picture rotation.

Not necessary Adjust now
OK

The �Programme Index table� is a quick and easy way to search for a channel you wish to view. The �Programme Index table� is only available in analogue mode. 1. Press the OK button to display the �Programme Index table� on screen.

DIGITAL

remote control to highlight �Not necessary� and press the OK button.
2 5 8 0 3 6 9

1 4 7

b) If some correction is required, press the V or v buttons on the remote control to highlight �Adjust now�, then press the OK button. Correct the slant by pressing the V or v buttons then press the OK button to store. 2. The autotune prompt screen appears. Press the OK button to select �Yes�. The autotune procedure begins.
The autotune prompt screen.
OK

OK

The Digital autotune display appears on screen and the search and store procedure begins. All the available Digital channels will now be captured and stored. As this may take some time, a message is included in the display to inform you of the tuning progress.

2. Press the v or V button to scroll through the list until the channel you wish to view is highlighted. 3. Press the OK button to display your chosen channel on the TV screen.

SECTION 1 GENERAL

When Digital tuning is complete, the analogue display appears automatically and the search and store procedure for the analogue channels begins.
Tuning the Digital channels.

The Channel Index menu
The �Channel Index menu� provides you with a quick and easy way to:a) b) c) d) View a complete list of the programmes available for selection, Obtain a preview of the programmes contained in the list, Search for a programme quickly by selecting from different categories of programmes, Store programmes into a list of favourites.

If no Digital and no analogue channels are found, a menu appears asking you to confirm your aerial is connected. After checking the aerial has been connected press OK to begin the autotune procedure again.

6 6 Getting Started

Once all Digital and analogue channels have been captured and stored, the TV returns to normal operation and displays the Digital channel captured on channel number 1.

Note:

If no Digital channels are captured, the analogue channel that is stored on channel number 1 is displayed.

Tuning the analogue channels.

Auto T uning

The �Channel Index menu� is only available in Digital mode.
02 C29 16%

3. To view programmes, press the PROG+/- buttons or the numbered buttons.

Programme: Channel : Completed

OK

1. Press the OK button on the remote control to display the �Channel Index menu� on the TV screen. The menu contains a list of all the available channels. The name of the programme currently being shown along with its start and finish times is shown for each of the available channels. The current channel is previewed in the top right corner of the screen with its channel name and number displayed below it. 2. Press the V or v buttons to move the coloured cursor up or down the list to select the desired programme. If you do not want to select a programme from the 6 channels listed, press the GREEN button to display the next 6 programmes or the RED button to display the preceding 6 channels. 3. Press the OK button to display the highlighted programme in the preview window*.

6. Finding the video channel
If you connected a VCR to your TV when following the �Connecting an aerial and a VCR� instructions, you will now need to find your video channel. Ensure the TV is in analogue mode. If it is not, press the DIGITAL/ button on the remote control. 1. Press the PROG +/- buttons on the remote control until the picture from the pre-recorded tape appears on the TV screen.
Notes: If you wish to move your video channel to a different programme number, refer to �The Set Up menu� section of this manual. If you have connected your VCR using a scart lead, press the / button on the remote control until the picture from the pre-recorded tape appears on the TV screen. (Refer to �Connecting additional equipment�).

4. Press the OK button to exit the �Channel Index menu�. The programme that was being previewed will be displayed.
*Note: If an age limit for viewing has been set and the programme selected exceeds that age limit, you will need to enter your PIN code before the preview is displayed. Refer to �The Main Menu� for more information on the �PIN Code� feature. Programmes that exceed the age limit you have set will be identified by a symbol.

Basic Operation

9