|
|
|
Kto jest w sklepie?
Sklep przegląda 6043 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
Carrying your monitor
Be sure to grasp the areas indicated by the arrows when carrying the monitor, and to use more than two people. Never grasp the front panel.
2
Pass a strong cord or a chain through each bracket mounted in step 1, and then secure it to a wall or a pillar, etc.
Step 2: Hookup
Using the rear RGB 1 IN connector
Rear of the monitor
Using the buckle
You can also use the supplied buckle to secure the monitor to the stand.
1 VIDEO IN 3 Y DVD VIDEO OUT S VIDEO
p for KL-W7000A
Before making the connection, turn off the power and disconnect the AC power cords of the monitor and the equipment to be connected. Refer to the instruction manual of the equipment you connect.
S VIDEO
CB/PB CR/PR
VIDEO
VIDEO L AUDIO R
Connecting to an IBM PC/AT or compatible computer
p for KL-W9000A
RGB
RGB 1 IN AUDIO R L
1
Attach the buckle to the stand on which the monitor is mounted. Tighten the supplied screw firmly.
Connect the RGB 2 IN connector on the front or the RGB 1 IN connector at the rear of the monitor to the video/audio outputs of the computer using the supplied RGB signal cable (D-sub 15 pin � D-sub 15 pin).
or
US
� 8 �
2
Stabilizing the monitor Using the brackets
After setting up, secure the monitor to a wall, etc. with the supplied brackets.
Belt
Using the front RGB 2 IN connector
Front of the monitor
RGB signal cable (supplied) or
Audio connecting cord (phono plug � 2 � stereo minijack) (not supplied)
VIDEO 2 IN VIDEO
INPUT SELECT
Insert the buckle until it clicks.
L AUDIO R
RESET
HD15�HD15 adaptor (supplied)*
RGB
AUDIO
Male side (without the No.9 pin) to video output to audio output
RGB 2 IN
1
Mount the two supplied brackets with the screws to the upper rear sides of the monitor.
IBM PC/AT or compatible computer
3
Pull the belt to fasten.
RGB signal cable (supplied) or
Audio connecting cord (stereo minijack � stereo minijack) (not supplied)
* The HD15�HD15 adaptor (supplied) may be needed for some models. The male side (without the No. 9 pin) of the adaptor should be connected to the computer.
Bracket (supplied)
HD15�HD15 adaptor (supplied)*
For customers using the supplied HD15�HD15 adaptor This monitor uses a No. 9 pin in the video signal connector for DDC1 and DDC2B compatibility. Some PC systems which are not compatible with either DDC1 or DDC2B may not accept the No. 9 pin. If you are not sure whether your PC system accepts the No. 9 pin or not, use the HD15 (Female) � HD15 (Male without the No. 9 pin) adapter (supplied).
Male side (without the No.9 pin) to video output to audio output IBM PC/AT or compatible computer
6-US
Getting Started
Getting Started
7-US
|
|
|
> |
|
