|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
KP-46WT510
3. Press the �9� button on the remote commander and �ne adjustment mode will be active where a green marker appears in the center of the screen. (In the case of GRN mode) 4. Press down on the joystick, and the marker color will be alternately switched between green (GRN mode) and white. 5. Press the �1� or �4� button on the remote commander, or use the joystick to move the marker to the position to be adjusted, where �ne adjustment can be made. * When the marker color is white: (in this case, �ne adjustment is disabled)
2-13.PJE ADJUSTMENT (SUB DEFLECTION ADJUSTMENT)
Adjustment type G R B H/V* H/V* H/V* O/O O/O O/O O/O -/O O/O O/O/O/O O/O O/O O/O -/O O/O O/O/O = Yes O/O O/O O/O O/O -/O O/O O/O/ = No
Adjustment item CENT SKEW SIZE LIN KEY PIN MLIN MSIZ
* H = Horizontal V = Vertical
Use the joystick to move the marker up, down, left, or right. * When the marker color is green: (GRN mode)
Note: If the value is over the limit value, adjust these in the �ne adjustment mode. Coarse Data Limit Value:
CENT H CENT V SIZE H BLUE H LIN RED H LIN
35 ± 170V 20 ± 170V -75 MAX -425 MIN 425 MAX
2-13-1.ADJUSTMENT FOR NTSC FULL MODE
� The adjustment should be done in the numerical order given. 1 4 : Moves the marker clockwise from the center to the outside. : Moves the marker counter clockwise from the outside to the center.
1) GREEN ADJUSTMENT
1. Cover the red and blue CRT lenses with lens caps to allow only green to show (or use the method shown in the note below for turning off the CRTs individually without using lens caps). Note: If lens caps are unavailable, you can cut off the unnecessary color beams by controlling the service mode 2150P-2 1 RGBS. 2. Enter the monoscope signal to set. 3. Select the PJE mode. 4. Press the �6� button on the remote commander to display the internal test signal (crosshatch). 5. Select �GRN CENT�, and adjust so that the pictures coincide in the center of screen. GRN CENT (Horizontally/Vertically)
* Fine adjustment can be made on the basis of a marker position using the joystick to move 5 6 3 or4.
Move joystick 5 direction
Move joystick 4 direction
CROSSHATCH
CROSSHATCH
Push the joystick to
Push the joystick to
6. Press the �9� button on the remote commander to return to coarse adjustment mode.
Push the joystick to
Push the joystick to
� 32 �
|
|
|
> |
|
