Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 6043 gości 
Kategorie
Informacje
Polecamy
Strona główna >> KENWOOD >> KRFA4020 Instrukcja Obsługi
 
 0 szt. w koszyku 

KENWOOD KRFA4020
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis KENWOOD KRFA4020 Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 18 (kliknij aby zobaczyć)
In case of difficulty
KRF-A4020 (En/E2T)

Resetting the Microcomputer

18

If the microcomputer may malfunction (unit cannot be operated, or shows an erroneous display) if the power cord is unplugged while the power is ON, or due to some other external factor. If this happens, execute the following procedure to reset the microcomputer and return the unit to its normal operating condition.

With the power cord plugged in, turn the POWER key OFF. Then, while holding down the ON/STANDBY key, press the POWER key.

� Please note that resetting the microcomputer will clear the contents of the memory and returns the unit to the state it was in when it left the factory.

Preparations Operations Other

Amplifier
Symptom No sound from the speakers. Cause � The speaker cords are disconnected. � VOLUME is set to the minimum position. � MUTE is ON. � The SPEAKERS switches are set to OFF. Remedy � Connect properly referring to �Setting the speakers�. 5 � Adjust the volume to a proper level. � Turn OFF the MUTE. ! � Set the SPEAKERS switch(es) to ON.

0

The standby indicator blinks and sound is not output.

� Speaker cords are short-circuited.

� Turn the power off, eliminate the shortcircuiting, then turn on the power again.

5

Sound is not output from one of the speakers. A humming noise is generated when the PHONO input selector is selected.

� The speaker cord is disconnected. � The audio cord from the turntable is not connected to the PHONO jacks. � The turntable is not grounded.

� Connect properly referring to �Setting the speakers�. 5 � Insert the audio cord plugs securely into the PHONO jacks. � Connect the grounding wire to the GND terminal on the rear panel. 4

Tuner
Symptom Radio stations cannot be received. Cause � No antenna is connected. � The broadcast band is not set properly. � The frequency of the desired station is not tuned. � Noise due to ignition noise from an automobile. � Noise due to interference from an electric appliance. � Noise due to a nearby TV set. � The preset station belongs to a frequency that cannot be received. � The preset memory was cleared because the power cord had been unplugged for a long period of time. Remedy � Connect an antenna. 5 � Set the broadcast band properly. � Tune the frequency of the desired station. # � Install the outdoor antenna away from the road. � Turn off the power to the appliance. � Install the receiver farther away from the TV. � Preset a station with a receivable frequency. � Preset the station again.

Interference.

A station which was preset cannot be received by pressing the corresponding numeric key.

Klienci kupując ten produkt kupili także

$4.99

KRFA4020 KENWOOD
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.174 - Number of Queries: 101 - Query Time: 0.048