CAUTION
� If the product emits smoke, strange odors or abnormal sounds, turn the power off and unplug it from the AC outlet, otherwise fire or electrical shock could result. Ask your dealer for repairs after confirming no smoke is present. � Only use devices that have been approved by us for use with this product, otherwise fire or electrical shock could result. � Do not remove or modify the covers, otherwise fire or electrical shock could result. � Do not place any container filled with liquid near the product or expose it to dripping, splashing, rain or moisture. � When connecting the product to the Pioneer-specified flat screen TV, unplug the TV�s power cord from the AC outlet before connection.
Attach the color sensor to the front panel (recommended)
When connecting the color sensor to the panel, unplug the panel�s power cord from the AC outlet. This is a simple and easy-to-attach method using a magnet. 1 Attach the color sensor at the bottom right of the front panel using a magnet (Fig. 1). 2 Attach the color sensor along the bottom edge of the front panel flush with the right side. 3 Connect the cable to the color sensor terminal on the rear upper bank but do NOT plug in to the power outlet (Fig. 2). Note � Use the cable clamps as necessary. � Remove the sheet of the double-sided adhesive tape when attaching the cable guide to the panel.
Attach the color sensor to the rear panel
When connecting the color sensor to the panel, unplug the panel�s power cord from the AC outlet. Methods of attaching the color sensor to the rear panel differ depending on the panel with or without side-mounted speakers. (when side-mounted speakers are installed) 1 Remove the screws of the color sensor then replace the bracket (Fig. 3). Use the removed screws again. 2 Loosen the upper two (2) speaker bracket screws.
3 Fit the color sensor bracket�s lower grooves into the screws (Fig. 4). Adjust the color sensor/speaker bracket positions so as to stay in place. 4 Fasten the screws. 5 Connect the cable to the color sensor terminal on the rear upper bank but do NOT plug in to the power outlet (Fig. 5). Note � Do not loosen the screws at the bottom of the panel. When attached to the rear panel, the sensor window points upward. � If the color sensor attached to the rear panel does not operate properly, attach it to the front panel. � Do not use the supplied screws when attaching the color sensor using the speaker brackets. � The color sensor may become hot due to a heat emitted from the panel. When using it in a high-temperature environment, attach the color sensor to the bottom of the front panel. (when side-mounted speakers are not installed) 1 Remove the screws of the color sensor then replace the bracket (Fig. 3). Use the removed screws again. 2 Finger tighten the supplied color sensor screws in the speaker screw holes. 3 Fit the color sensor bracket�s lower grooves into the screws (Fig. 6). Adjust the bracket position to stay in place. 4 Fasten the screws. 5 Connect the cable to the color sensor terminal on the rear upper bank but do NOT plug in to the power outlet. Note � If the color sensor attached to the rear panel does not operate properly, attach it to the front panel. � The color sensor may become hot due to a heat emitted from the panel. When using it in a high-temperature environment, attach the color sensor to the bottom of the front panel. � Do not use the screws supplied for the speakers. Important The color sensor may not operate properly: � if attached by methods other than specified above � if anything blocks light falling on the sensor window � if light falls on only part of the sensor window � if the light falling on the sensor window and the panel screen differs
Activate the color sensor
To activate the color sensor, follow the procedure below. �HOME MENU���Picture���AV Selection���OPTIMUM� or �HOME MENU���Option���Room Light Sensor���Mode 1� or �Mode 2� (For details on �Mode 1� and �Mode 2�, refer to �Room Light Sensor� in the operating instructions supplied with the flat screen TV.) Specifications Weight: 0.08 kg (see the Color Sensor illustration for dimensions.) Max. current consumption: 50 mA or less
