|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
- Specifications
- Connectors
- Self Diagnostic Software
- GENERAL
- Switching On the TV and Automatically Tuning
- Introducing the Menu System
- Teletext
- Connecting Optional Equipment
- Using Optional Equipment
- Troubleshooting
- DISASSEMBLY
- Rear Cover Removal
- A Board PWB Removal 1
- A Board PWB Removal 2
- Service Position
- Wire Dressing
- Picture Tube Removal
- Rear Cover Removal
- Chassis Removal
- Service Position
- Wire Dressing
- Picture Tube Removal
- SET - UP ADJUSTMENTS
- Beam Landing
- Convergence
- Focus Adjustment
- Screen (G2), White Balance
- CIRCUIT ADJUSTMENTS
- Electrical Adjustments
- Test Mode 2
- DIAGRAMS
- Circuit Board Location
- Block Diagrams
- Schematic Diagrams and Printed Wiring Boards
- Semiconductors
- IC Blocks
- EXPLODED VIEWS
- Chassis (KV - 21LT1)
- Chassis (KV - 21FT2)
- Picture Tube (KV - 21LTl)
- Picture Tube (KV - 21FT2)
- ELECTRICAL PARTS LIST
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
Layout of each control
3-4. Screen (G2), White Balance
[Adjustment in the service mode using the remote commander] G2 adjustment 1. 2. 3. Input a dot signal from the pattern generator. Set the Picture, Brightness and Colour to minimum. Apply 175V DC from an external power supply to the R, G and B cathodes of the CRT. Whilst watching the picture, adjust the G2 control [SCREEN] located on the Flyback Transformer to the point just before the flyback return lines disappear. White balance adjustment for TV mode 1. 2. Input an all-white signal from the pattern generator. Enter into the �Service Mode� by pressing �TEST�, �TEST� and �MENU� on the Service Commander. 3. Select �Service� from the on screen menu display and press the right arrow button on the remote commander. 4. The �Service� menu will appear on the screen. [See Page 18] 5. Set the �Contrast� to MAX. 6. Set the �R-Drive� to 25. 7. Adjust the �G-Drive� and the �B-Drive� so that the white balance becomes optimum. 8. Press the �OK� button to write the data for each item. 9. Set the �Contrast� to MIN. 10. Adjust the �G-Cutoff�, and the �R-Cutoff� with the left and right buttons on the remote commander so that the white balance becomes optimum. 11. Press the �OK� button to write the data for each item.
V.STAT
Purity BMC (Hexapole)
4.
3-3. Focus Adjustment
1. 2. 3. Receive a television broadcast signal. Normalize the picture setting. Adjust the focus control located on the flyback transformer to obtain the best focus at the centre of the screen. Bring only the centre area of the screen into focus, the magenta-ring appears on the screen. In this case, adjust the focus to optimize the screen uniformly.
Focus
Screen
17
|
|
|
> |
|
