Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 6043 gości 
Kategorie
Informacje
Polecamy
Strona główna >> MACKIE >> M2600 Instrukcja Obsługi
 
 0 szt. w koszyku 

MACKIE M2600
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis MACKIE M2600 Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 24 (kliknij aby zobaczyć)
You can connect an unbalanced XLR cable to the M�2600, although this would be unusual � as unusual as an unbalanced XLR output. However, if you have an unbalanced XLR connection to make, refer to the �Connectors� section (Appendix C) at the back of this manual for more information.
SHIELD HOT

To use the THRU outputs, connect your source equipment into the first amp�s INPUTs as usual, then patch from that amp�s THRU jacks to the next amp�s INPUTs, and so on, daisy-chaining as many amps as you want for your application. A general rule of thumb is to maintain a load impedance

2

COLD SHIELD

3 1

1

COLD 3 HOT

2
SHIELD COLD

1 3 2

10 times or more than the source impedance to prevent excessive loading. If your console has an output impedance of 100 ohms, then you can daisy-chain up to twenty M�2600 amplifiers, which presents a load of 1200 ohms to the console (input impedance of 24 kohms divided by 20 amplifiers = 1200 ohms). The THRU jacks can also be used to relay the signal on to other devices such as a DAT or cassette recorder, enabling you to record exactly what the audience is hearing. In the THRU position of switch , the THRU jacks are wired straight from the XLR and TRS INPUTs � so the signal coming out of the THRU jacks is exactly the same as the signal going into the amplifier. You can also use the 1/4" TRS INPUT jacks as THRU jacks, (not affected by switch or by the LOW CUT FILTER ). Connect the 1/4" TRS INPUT jacks on the first amplifier to the TRS 1/4" INPUT jacks on the second amplifier using 3-conductor shielded cables with TRS plugs on both ends. Warning: If you use a regular guitar cord with 2-conductor TS plugs, you�ll unbalance the signal at the XLR input by grounding the low side (�) of the signal (pin 3).

HOT

Balanced XLR Connectors: Apollo/Soyuz Rendezvous

The M�2600 amp expects to see a nominal signal level anywhere between the �10 dBV �semipro� and +4 dBu �pro� standards, meaning almost any line-level mixer or other device can be plugged into the amp�s INPUTs. Use the GAIN controls to adjust the gain of the amplifier to match the signal level you�re using.

THRU and

THRU SWITCH

Someday you�ll do a show at NudeStock and realize that one M�2600 amplifier is just not going to do the job � you�ll need a six-foothigh rack full of �em to hide behind. That�s what the THRU jack is for. It has three modes of operation, depending on the setting of the THRU switch : � THRU, a straight copy of what�s going into the amplifier, nothing added or taken away from your big finish on spoons. � LOW OUT, the lower frequencies only, below the frequency set by the CROSSOVER switch . � HIGH OUT, the higher frequencies only, above the frequency set by the CROSSOVER switch . Note that the LOW OUT and HIGH OUT are also affected by the setting of the LOW CUT FILTER .

LOW CUT FILTER
Every woofer has frequency response specifications. It�s usually expressed in Hertz (or cycles per second), like �40Hz�300Hz.� The �40Hz� refers to the low-frequency point (usually, but not always) where the speaker�s output drops by 3 dB, and will �roll off� completely as the frequency goes down. There is no point in sending a woofer any frequencies it can�t reproduce � you can�t hear it, and worse yet, it�s a waste of amplifier power that can be better used reproducing frequencies you can hear.

24

Klienci kupując ten produkt kupili także

$4.99

M2600 MACKIE
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.161 - Number of Queries: 105 - Query Time: 0.041