PHILIPS MC70
Instrukcja Serwisowa

Basic Functions
English English
You can select desired brightness for the For optimal sound listening, you are only display. able to select BASS/TREBLE or wOOx at a

Notes: In Eco Power Standby mode Interactive Sound Control Dim mode � When power is turned on, the disc tray may q Press ECO POWER. open and close initialise the system. § The system will switch to last selected source. � If you do not complete Plug and Play installation, q Press CD 123, TUNER, TAPE or AUX/CDR Plug and Play will be reinitiated next time you on the remote control. q Press DIM on the remote control repeatedly to time (for model MC-70 only). turn on power. § The system will switch to the selected source. select 1, 2, 3 or DIM OFF display � If no stereo frequency is detected during mode. wOOx (for model MC-70 only) Plug and Play, "CHECK ANTENNA" will be § and the corresponding mode number will There are three wOOx settings to enhance the DIM Switching the system to Standby appear on the display, except for DIM OFF mode. displayed. bass response. � During Plug and Play, if no button is pressed

mode
q Press wOOx on the system repeatedly to In Demonstration mode music level bar active. OR q Press and hold DEMO STOP on the system. wOOx effect. In any other source mode (except Eco Power Standby mode)

within 15 seconds, the system will exit Plug and DIM OFF ......... All available LEDs light up, display Play mode automatically. screen will have full brightness, select next wOOx level or switch off the

+

Demonstration mode DIM 1 ............... Some LEDs light up, display
screen will have full brightness, control). 1 2 DIM 2 ............... All lightings turn off, display

The system has a demonstration mode that shows various features offered by the system. =

q Press STANDBY ON (or B on the remote music level bar inactive. =

To activate demonstration § The clock will appear on display when the screen will have full brightness,

music level bar inactive. ON (enhanced) or OFF (normal) the wOOx sound effect.

1

Press wOOx on the remote control to switch q In mode, press and hold DEMO system is in Standby mode. STOP on the system until "DEMO DEMO ON" ON is displayed. § The demonstration will begin.

DIM 3 ............... All lightings turn off, display

Switching the system to Eco screen will be at half brightness, 2 When is switched on, press wOOx Power Standby mode (< 1 Watt) LEVEL on the remote control repeatedly to
remote control). 2, 3 or WOOX OFF. q Press and hold DEMO STOP on the system

music level bar inactive.

q Press ECO POWER (or press and hold B on select the desired wOOx level : WOOX 1, To deactivate the demonstration + music level bar

2-5

until "DEMO OFF" is displayed. § "ECO ECO PWR" PWR will be displayed, then the § If �WOOX WOOX 1, 1 2 or 3 "� is selected, DEMO OFF § The system switch to Standby mode. display screen will go blank. and the corresponding level Volume Control WOOX § The low power ECO POWER LED will be number will appear on the display. Adjust VOL to increase (turn knob clockwise or lighted. press VOLUME +) or decrease (turn knob antiNote: � Even if you remove the AC power cord and reconnect it to wall socket, the demonstration Note: § "-XX -XX dB" dB will be displayed. "XX XX" XX denotes Notes: will remain off until activate again. � If you have not deactivated the demonstration, it to Eco Power or Standby mode. § When reached the minimum volume level, Bass/Treble will resume automatically. q Press STANDBY ON. volume. If this occurs, deactivate wOOx or reduce
PHONES

§ If �WOOX WOOX OFF"� OFF is selected, the

wOOx sound effect will be switched off. will resume five seconds after the system switches volume level. � When switched off wOOx effect, the last

clockwise or press VOLUME -) the sound level.

"VOL VOL MUTE" will displayed. MUTE � Some discs or tapes might be recorded in high

Switching the system on Power Saving Automatic Standby To listen through the headphones
As a power-saving feature, the system will q Connect headphones plug § The system will switch to last selected the volume. automatically switch to Standby mode if you do to PHONES socket at the source. front of the system. q Press 3CDC (CD 123), TUNER, TAPE, disc or tape has stopped playing. § The speakers will be muted. AUX/CDR. not press any buttons within 30 minutes after a

In Standby/Demonstration mode modulation, which causes a distortion at high

§ The system will switch to the selected source. To switch off the volume temporarily (DISC 1 DISC2 / DISC 3) button. q Press MUTE on the remote control. § The system will switch to CD mode. § Playback will continue without sound and "MUTE MUTE" MUTE will be displayed. q To restore the volume, press MUTE again or increase the volume level.

q Press any one of the disc OPEN�CLOSE

13 14