|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Schematy są ale można wysilić się i zrobić kolorowy skan i o większej rozdzielczości. Wtedy schematy płytek będą czytelniejsze. Całość super jako wartość merytoryczna. Wszystkie dane potrzebne do podłączenia różnego rodzajów urządzeń takich gramofon, CD itd.
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
MC-UG775-00
3 REPLACEMENT INSTRUCTIONS
3.1.
3.1.1.
Lower Plate Replacement
Removal
1. Before servicing any parts, disconnect vacuum from electrical outlet. 2. Place paper under nozzle whenever lower plate is removed to protect floor. 3. Place handle in upright position and turn vacuum over to expose lower plate.
2. Place the belt around the agitator pulley on the agitator assembly. 3. Start the new agitator assembly back into the nozzle housing by placing the slide arch back into the agitator end cap, then the side opposite the belt partially into the nozzle housing slot. The small tabs should be aligned with the nozzle and the other against the lower plate. This will hold the agitator in place and leave both hands free to place enough tension on the belt to allow the other side of the agitator to return into the nozzle housing slot. 4. Use both hands to pull the belt tight, slide the agitator assembly firmly into the slots on each end of the nozzle housing. 5. Rotate the agitator assembly by hand to insure nothing rubs and to check for correct assembly. 6. Replace the lower plate as outlined in the Lower Plate Replacement section.
4. Release lower plate by pressing two (2) latches inward. 5. Press on two (2) tabs inward and lift lower plate. 6. Remove lower plate and remove any residue that may exist in belt area.
3.1.2.
Installation
1. Hook the front of the lower plate into the slots on the front of the nozzle housing. Press the lower plate down into place. 2. Fasten the lower plate by pushing the two (2) latches outward. 3. Ensure the two (2) tabs latched. NOTE: For general servicing, it is necessary to eliminate pinching of any wire during reassembly. After servicing any electrical component or electrical enclosure, the unit should be reassembled and checked for dielectric breakdown or current leakage.
3.3.
Brush Replacement
3.2.
3.2.1.
Agitator Assembly Replacement
Removal
1. The agitator brushes should be replaced when the brushes are worn. Brushes should be checked by holding a card across the lower plate. If the bristles on the agitator assembly do not touch the card you should replace all the brushes for best cleaning results.
1. The brushes are replaceable separately. When the brushes need replacing, the agitator assembly will have to be removed. 2. Remove the lower plate as outlined in the Lower Plate Replacement section. 3. Remove the agitator assembly as outlined in the Belt Replacement section. .
3.3.1.
Removal
1. Remove the lower plate as outlined in the Lower Plate Replacement section. 2. Remove the agitator assembly as outlined in the Agitator Assembly Replacement section.
3.2.2.
Installation
1. Place the belt around the motor shaft.
11
|
|
|
> |
|
