|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Schematy są ale można wysilić się i zrobić kolorowy skan i o większej rozdzielczości. Wtedy schematy płytek będą czytelniejsze. Całość super jako wartość merytoryczna. Wszystkie dane potrzebne do podłączenia różnego rodzajów urządzeń takich gramofon, CD itd.
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
NOZZLE HOUSING REMOVAL/INSTALLATION
REMOVAL
1. Turn the vacuum cleaner over exposing the underside. Release the nozzle housing by removing the five (5) screws that secure the nozzle housing, (Fig 4). 2. After removing screws turn the vacuum cleaner back over and remove hoses from top cover, (Fig 4). 3. Remove the screw holding the Bare Floor/Carpet selector switch and remove the switch. 4. Remove the nozzle housing by grasping the snap at the back just behind the agitator housing, lift up, pivoting it toward the agitator until it releases from the slots in front. Remove any residue that may exist in the belt area.
Snap
EXPLODED VIEW (MOTOR HOUSING, MOTOR, AND BODY)...
BLOCK C
Hose
C-41
Bare Floor Selector Switch C-3 Hose C-5
C-2
C-4
INSTALLATION
Nozzle Housing Cover
C-8
(Fig. 1) 4)
1. Hook the front of the nozzle housing into the slots on the front of the nozzle housing. Press the lower plate down into place. The housing will snap into place. 2. Replace the five (5) lower plate mounting screws. 3. Replace the Bare Floor selector switch and screw.
C-9
C-6
C-7
C-1
AGITATOR ASSEMBLY REMOVAL/INSTALLATION
Note: Before removal make sure the Bare Floor/Carpet Selector is in bare floor mode.
Gear Box Screw C-12 Flat Belt Flat Idler Pulley Rear Agitator Gear Box Shaft C-14 C-26 C-15
C-10 C-13
Removal
The brushes are not replaceable separately. When brushes need replacing, the agitator assembly will be have to be replaced. 1. Remove the lower plate as outlined in NOZZLE HOUSING REMOVAL/ INSTALLATION section. 2. Remove the screw holding the gear box in place. Carefully lift up on the gear box, agitator and bearing unit assembly, until it clears both sides of the lower plate, (Fig. 5). 3. Carefully remove the front agitator from gear box. Remove flat belt from front agitator. The complete assembly can then be lifted free from lower plate.
Front Agitator Gear Box Lower Plate
C-34
C-16 C-33 C-28 C-30 C-17 C-29 C-31
C-11 C-23 C-13 C-10 C-12
C-19
Bearing Unit
(Fig. 5)
C-36 C-25 C-32 C-24
Installation
1. Place the flat belt around front agitator (Fig. 5). 2. Carefully insert the shafts of the gear box into both agitators.
C-18 C-22 C-7 C-40
C-39
C-27
C-37
3. Start the new assembly back into the lower plate by placing the bearing unit partially into the slot. 4. With the belt in place, carefully place the gear box in position. The complete assembly should be now in place and ready to fasten in with the gear box screw. 5. Rotate the agitator assembly by hand to insure nothing rubs and to check for correct assembly. 6. Replace the nozzle housing cover as outlined in the LOWER PLATE REMOVAL/INSTALLATION section.
C-38 C-20 C-21
C-35
- 14 -
-7-
|
|
|
> |
|
