jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
Tekstowy podgląd strony 31 (kliknij aby zobaczyć)
MDS-JE770
5-7. INITIAL SETTING OF ADJUSTMENT VALUE
Note: Mode which sets the adjustment results recorded in the non-volatile memory to the initial setting value. However the results of the temperature compensation offset adjustment will not change to the initial setting value. If initial setting is performed, perform all adjustments again excluding the temperature compensation offset adjustment. For details of the initial setting, refer to �5-4. Precautions on Adjustments� and execute the initial setting before the adjustment as required. Setting Procedure : 1. Rotate the l AMS L knob to display �ADJCLEAR� (C28). 2. Press the YES button. �Complete!� will be displayed momentarily and initial setting will be executed, after which �ADJ CLEAR�(C28) will be displayed.
5-9. TEMPERATURE COMPENSATION OFFSET ADJUTMENT
Save the temperature data at that time in the non-volatile memory as 25 �C reference data. Note : 1. Usually, do not perform this adjustment. 2. Perform this adjustment in an ambient temperature of 22 �C to 28 �C. Perform it immediately after the power is turned on when the internal temperature of the unit is the same as the ambient temperature of 22 �C to 28 �C. 3. When D101 has been replaced, perform this adjustment after the temperature of this part has become the ambient temperature. Adjusting Procedure : 1. Rotate the l AMS L knob and display �TEMP ADJUS� (C03). 2. Press the YES button and select the �TEMP ADJUS�(C03) mode. 3. �TEMP = [OK]� and the current temperature data will be displayed. 4. To save the data, press the YES button. When not saving the data, press the MENU/NO button. 5. When the YES button is pressed, �TEMP = SAVE� will be displayed and turned back to �TEMP ADJUS�(C03) display then. When the MENU/NO button is pressed, �TEMP ADJUS� (C03) will be displayed immediatelly. Specified Value : The �TEMP = � should be within �E0 - EF�, �F0 - FF�, �00 0F�, �10 - 1F� and �20 - 2F�.
5-8. RECORDING AND DISPLAYING THE Iop INFORMATION
The IOP data can be recorded in the non-volatile memory. The Iop value on the label of the optical pick-up and the Iop value after the adjustment will be recorded. Recording these data eliminates the need to read the label on the optical pick-up. Recording Procedure : 1. While pressing the l AMS L knob and x button, connect the power plug to the outlet, and release the l AMS L knob and x button. 2. Rotate the l AMS L knob to display �[Service]�, and press the YES button. 3. Rotate the l AMS L knob to display �Iop.Write�(C05), and press the YES button. 4. The display becomes Ref=@@@.@ (@ is an arbitrary number) and the numbers which can be changed will blink. 5. Input the Iop value written on the optical pick-up. To select the number : Rotate the l AMS L knob. To select the digit : Press the l AMS L knob 6. When the YES button is pressed, the display becomes �Measu=@@@.@� (@ is an arbitrary number). 7. As the adjustment results are recorded for the 6 value. Leave it as it is and press the YES button. 8. �Complete!� will be displayed momentarily. The value will be recorded in the non-volatile memory and the display will become �Iop Write�(C05). Display Procedure : 1. Rotate the l AMS L knob to display �Iop.Read�(C26) and press the YES button. 2. �@@.@/##.#� is displayed and the recorded contents are displayed. @@.@ indicates the Iop value labeled on the pick-up. ##.# indicates the Iop value after adjustment 3. To end, press the l AMS L button or MENU/NO button to display �Iop Read�(C26).
5-10. LASER POWER ADJUSTMENT
Check the Iop value of the optical pick-up before adjustments. (Refer to 5-8. Recording and Displaying Iop Information.)
Laser power meter
Optical pick-up objective lens Digital volt meter
BD board CN105 pin 1 (I+3V) CN105 pin 2 (IOP)
Connection : Adjusting Procedure : 1. Set the laser power meter on the objective lens of the optical pick-up. (When it cannot be set properly, press the m button or M button to move the optical pick-up.) Connect the digital volt meter to CN105 pin 1 (I+3V) and CN105 pin 2 (IOP). 2. Rotate the l AMS L knob and display �LDPWR ADJUST�(C04). (Laser power : For adjustment) 3. Press the YES button once and display �LD 0.9 mW $ �. 4. Rotate the l AMS L knob so that the reading of the laser power meter becomes the specified value. Press the YES button after setting the range knob of the laser power meter, and save the adjustment results. (�LD SAVE $ � will be displayed for a moment.) 5. Then �LD 7.0 mW $ � will be displayed. 6. Rotate the l AMS L knob so that the reading of the laser power meter becomes the specified value, press the YES button and save it. Note : Do not perform the emission with 7.0 mW more than 15 seconds continuously. 31
