Gruba instrukcja - poprostu wszystko co potrzreba - polecam .
Tekstowy podgląd strony 5 (kliknij aby zobaczyć)
Getting Started
READ THIS PAGE!!
Even if you�re one of those people who never read manuals, all we ask is that you read this page now before you begin using the Onyx 1620. You�ll be glad you did! 3.
a line input such as a CD player or tape recorder output. Be sure that the volume of the input source is the same as it would be during normal use. If it isn�t, you might have to readjust these levels during the middle of the set. Adjust the channel�s GAIN control so that the LEDs on the RIGHT meter stay around �0� and never go higher than �+7.� If you�d like to apply some EQ, do so now and return to step 3. Remember to push in the EQ IN/OUT button or the EQ controls won�t do anything. Disengage that channel�s SOLO switch. Repeat for each channel.
4.
Zero the Controls
1. 2. 3. Turn down the channel GAIN, AUX, and Fader controls, and center the channel EQ and PAN controls. Set all push button switches to their �out� positions. In the output section (right hand side), turn all the rotary knobs �down,� the switches �out,� and the MAIN MIX fader down. Turn the POWER switch off.
5. 6.
Instant Mixing
1. Leave the microphone plugged into channel 1 and connect a keyboard, guitar or other instrument to channel 2. Be sure to �Set the Levels� for channel 2 as described above. To get sound out of the speakers, turn up channel 1 and 2 faders to the �U� mark and slowly turn up the MAIN MIX fader to a comfortable listening level. Sing and play. You�re a star! Adjust the faders for channels 1 and 2 to bring your voice and your instrument up and down to create your own mix.
4.
Connections
If you already know how you want to connect the Onyx 1620, go ahead and connect the inputs and outputs the way you want them. If you just want to get sound through the mixer, follow these steps: 1. 2. Plug a microphone or other signal source into channel 1�s MIC or LINE input. Plug in the detachable linecord, connect it to an AC outlet, and turn on the Onyx 1620�s POWER switch. Connect cords from the Onyx 1620�s MAIN OUTS (XLR connectors on the rear panel and 1/4" TRS connectors on the front panel) to your ampli�er. 4. Hook up speakers to the amp and turn it on. If the ampli�er has level controls, set them however the manufacturer recommends (usually all the way up).
2.
3.
Other Nuggets of Wisdom
� For optimum sonic performance, the channel and MAIN MIX faders should be set near the �U� (unity gain) markings. Always turn the MAIN MIX fader and CONTROL ROOM knob down before making connections to and from your Onyx 1620. When you shut down your equipment, turn off the ampli�ers �rst. When powering up, turn on the ampli�ers last. Never listen to loud music for prolonged periods. Please see the Safety Instructions on page 2 for information on hearing protection. � Save the shipping box! You may need it someday, and you don�t want to have to pay for another one.
3.
�
�
Owner�s Manual
Set the Levels
To set the channel GAIN controls, it�s not even necessary to hear what you�re doing at the outputs of the mixer. If you want to listen while you work, plug headphones into the PHONES jack on the front panel, then set the PHONES knob about one-quarter of the way up. The following steps must be performed one channel at a time. 1. Push in the channel�s SOLO switch. Make sure the SOLO MODE switch is up (PFL). 2. Play something into the selected input. This could be an instrument, a singing or speaking voice, or
�
That�s it for the �Getting Started� section. Next comes the �Hookup� section that shows you some typical ways that you might use the Onyx 1620 in real applications. After that, you can take the grand tour of the mixer, with descriptions of every knob, button, input, and output. We encourage you to take the time to read all of the feature descriptions, but at least you know it�s there if you have any questions. Owner�s Manual
