FLM P1033E
Instrukcja Obsługi

Starting and Stopping
To Start your Lawnmower 1. Connect female extension cable connector to the back of the switchbox. 2. Form loop in mains cable and push the loop through the slot in the cable restraint (M) 3. To secure, position loop over the hook and pull the cable back through the slot.(N). 4. Connect plug to mains and switch on. 5. Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn damage whilst starting. The switchbox is provided with a lock-off button (P1) to prevent accidental starting. 6. Press and hold the lock off button on the switchbox,(P1) then squeeze the Start/Stop lever towards the upper handle as shown on Fig. Q. 7. Continue to squeeze the start/stop lever towards the upper handle and release the lock-off button.(R) 8. Lower the lawnmower to its proper operating position and commence mowing. To Stop your Lawnmower 1. Release the pressure on the Start/Stop lever.

How to Mow
1. For the best results, mow the outside edge of the lawn in a clockwise direction first.(S1) 2. Then start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have already cut. (S2) 3. For best grass collection, always mow in a straight line, do not swing the lawnmower from side to side. Do Not Overload Your Mower Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor speed drops you may overload your lawnmower which may cause damage. When mowing in long thick grass a first cut with the cutting height set higher will help reduce the load. See Adjusting the Cutting Height. Mow twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one time and this may also result in poor collection.

Removing and Fitting the Blade and Fan
T1 - Blade bolt T2 - Blade T3 - Fan � Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Removing the Blade and Fan 1. To remove the blade bolt, hold the fan firmly and with the spanner provided loosen the blade bolt by turning it anti-clockwise (T). 2. Remove the blade bolt, blade and fan. (T) 3. Inspect for damage and clean as necessary. � Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner - regardless of condition. � If the blade is cracked or damaged replace it with a new one. � Never use a blade bolt if the insulated head is damaged cracked or missing. Fitting the Blade and Fan 1. Ensure the fan is located correctly.(T) 2. Fit the blade to the fan with the tilt edges of the blade (T4) facing towards the mower, ensuring the blade is located onto the fan location points (T5) correctly 3. Re-assemble blade bolt through blade and fan. 4. Hold the fan firmly and tighten blade bolt firmly with the spanner provided. Do not over tighten. 5. Do not use a longer spanner.

Caring for your Lawnmower
Cleaning (V) � USE GLOVES � IMPORTANT It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a potential fire hazard. 1. Remove grass from under the deck with brush. 2. Using a soft brush - remove grass clippings from all air intakes, the discharge chute and the grass box. 3. Remove the blade, see Figure T, to gain access to the fan and clean with a soft brush. 4. Wipe over the surface of your lawnmower with a dry cloth. � IMPORTANT Never use water for cleaning your lawnmower. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts. At the End of the Mowing Season 1. Replace blade, bolts, nuts or screws, if necessary. 2. Clean your lawnmower thoroughly. 3. Make sure that the electric cable is coiled properly. Storing your Lawnmower Store in a dry place where your lawnmower is protected from damage.

Service Recommendations
� Your product is uniquely identified by a silver and black product rating label. � We strongly recommend that your product is serviced at least every twelve months, more often in a professional application.

ENGLISH - 3