|
|
|
Kto jest w sklepie?
Sklep przegląda 6043 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
5-1. Trouble Diagnosis
No
1
Item
The power is not supplied
Cause and treatment
- Is the PCB connector connected well? - Is the voltage normal? - Is the power supply plug connected well? - Is the noise filter connected well? - Is the secondary output of the power supply transformation normal? - Is the fuse disconnected? (option) � If above points are not found, the PCB assembly is out of order. Replace it. - Is the knob open? - Did you push START/PAUSE button after selecting the course? - Is the water supply valve connected well? - Is the winding of the water supply valve continuous? - Is the connection and operation of the pressure switch normal? � If above points are not found, the PCB assembly is out of order. Replace it. - Is the connection and operation of the pressure switch normal? - Is the pressure switch hose damaged so that the air is leaked? - Is the pressure switch hose bent? - Check the operation of the water level switch. � If above points are not found, the PCB assembly is out of order. Replace it. - Is the belt connected well? - Is the winding of the motor continuous? (Rotor winding, stator winding, generator) - Is the motor protector normal? � If above points are not found, the PCB assembly is out of order. Replace it. - The PCB assembly is out of order. Replace it. (Inversion relay open trouble) - Is the drainage hose bent? - Is the winding of the drainage pump continuous? - Is the drain filter clogged by the waste? � If above points are not found, the PCB assembly is out of order. Replace it. - The unbalance is detected. - Put in the laundry uniformly and start again. - Is the pulley nut loosen? - Is the transport safety device removed? - Is the product installed on the level and stable place? (Little noise may be generated during the high-speed SPIN.) <When the leak breaker and current breaker is installed separately> - When the leak breaker is down, check and make the earth of the outlet. - When the current is down, the current is leaked. <Is the breaker down when the leak/current breaker is combined?> - Check the rated capacity of the current and leak breaker. The current breaker may be down due to the lack of the current when the wash machine and other apparatus are used. In this case, execute the cold water wash to check whether the current capacity is lack. - Is the wash heater terminal unplugged? - Is the wash heater normal? - If above points are not found, the PCB assembly is out of order. Replace it.
2
The water is not supplied.
3
The wash does not start though the water supply is stopped.
4
The drum does not rotate during washing.
5
The drum rotates by one direction during washing. (The drum rotates to one direction for SPIN.) Drainage problem.
6
7 8
Dehydration problem. Abnormal noise during SPIN.
9
Leak breaker or current/leak breaker is down during washing.
10
The heating is not executed.
8
SAMSUNG ELECTRONICS CO., LTD
|
|
|
> |
|
