jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
: IN : The photo sensor signal input. : IN : The photo sensor signal input. : IN : The photo sensor signal input. : O : The motor drive signal output. : O : The motor drive signal output. : O : The motor drive signal output. : O : The motor drive signal output. : O : The motor drive signal output. : O : The motor drive signal output. : O : The reset pulse output. : O : Digital mute signal output. : O : The test terminal. : IN : Illumination ON signal input. : IN : For the test. : IN : For the test. : IN : For the test. : IN : For the test. : IN : The serial data input from EEP-ROM. : O : The serial data output to EEP-ROM. : O : The clock pulse output to EEP-ROM. : O : The chip enable pulse output to EEPROM. : IN : The destination setting signal input. : IN : The destination setting signal input. : O : The clear signal output for the test mode indication. : O : The clock pulse output to LED driver. : O : The strobe pulse output to LED driver. : O : The clear pulse output to LED driver. : O : The serial data output to LED driver. : O : The illumination ON signal output. : IN : The key scan intput terminal. : IN : The key scan intput terminal. : IN : The key scan intput terminal. : IN : The key scan intput terminal. : O : The key scan output terminal. : O : The key scan output terminal. : IN : The shutter signal input. : - : Ground. : IN : The analog voltage input for illumination signal. : - : VDD reference voltage. : - : Positive supply voltage. : IN : Sub Q data input from the CD IC. : - : Not in use.
1.Terminal Description pin 1: SQCK pin pin pin pin pin pin pin pin 2: DIMMER 3: ILL PULSE 4: TCLK 5: NU 6: CONNECT G 7: M LD O 8: NU 9: RESET
: O : CD DSP SQCK. : O : The diminution pulse output to the illumination. : IN : Illumination control signal input. : O : The test clock output. : - : Not in use. : - : Connect to the ground. : O : Load command output to CD-IC. : - : Not in use. : IN : Reset signal input. : O : Crystal connection. : - : Ground. : IN : Crystal connection. : - : Positive supply voltage.
pin 44: M 1 CCW pin 45: M 1 CW pin 46: M 3 CCW pin 47: M 3 CW pin 48: RST OUT pin 49: D MUTE pin 50: HSSW1 pin 51: ILL pin 52: TEST 4 pin 53: TEST 3 pin 54: TEST 2 pin 55: TEST 1 pin 56: EEP DI pin 57: EEP DO pin 58: EEP CLK pin 59: EEP CE pin 60: Destination 1 pin 61: Destination 2 pin 62: T CLR pin 63: LED CLK pin 64: LED STB pin 65: LED CLR pin 66: LED DATA pin 67: ILL ON pin 68: K IN 0 pin 69: K IN 1 pin 70: K IN 2 pin 71: K IN 3 pin 72: K OUT 0 pin 73: K OUT 1 pin 74: SHUT pin 75: GND pin 76: ILL AD pin 77: VDD REF pin 78: VDD pin 79: SUB Q pin 80: NU
pin 10: X OUT pin 11: GND pin 12: X IN pin 13: VDD
pin 14: CONNECT VDD : - : Connect to the VDD. pin 15: BLKCK : IN : The sub code block clock input. pin 16: ACC DET pin 17: BU DET pin 18: SW 9V pin 19: BEEP pin 20: REQ O pin 21: ILL CNT pin 22: T DATA pin 23: PON 2 pin 24: TX pin 25: RX pin 26: NU pin 27: A MUTE pin 28: M DATA pin 29: STAT pin 30: M CLK pin 31: LIMIT pin 32: SW 1 pin 33: SW 2 pin 34: EPM pin 35: P ON 1 pin 36: PT 2 pin 37: PT 5 pin 38: PT 4 : IN : ACC detection signal input. : IN : Backup detection signal input. : O : 9V power supply control. : O : Beep out. : O : Transmit request signal output. : O : The illumination control. : O : The display data output for the test mode indication. : O : Power ON signal output. : O : Serial data output of N-BUS. : IN : Serial data input of N-BUS. : - : Not in use. : O : The audio mute signal output. : O : The command data output to the CD IC. : IN : The status data input from the CD IC. : O : The clock puse output to the CD IC. : IN : Sled limit switch signal input. : IN : The switch signal input. : IN : The switch signal input. : IN : Pull down. : O : Power ON signal output. : IN : The photo sensor signal input. : IN : The photo sensor signal input. : IN : The photo sensor signal input.
