jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
Tekstowy podgląd strony 6 (kliknij aby zobaczyć)
051-2055-00
+
-
TDA8593J/N3 I2C-bus controlled Audio Power Amplifier
R Frnt O8
051-4617-90
LA1061M-TE-L
Antenna Switching Controller
13
R Frnt O+ 10
Weak field comparator SQ 6 5 Strong field comparator 10k RQ Count 30k Flip Flop CTR DAC reset Mono Multi. 12 11 10 8 VCC 7 GND Mono Multi. A G C 3
P GND 1 9
I2C-bus
+
Clip det Diagnos
14 1
SVref 11 R Frnt In 12
L Rear O+ 22
+
P GND 3 19
-
-
R Rear In 13
Noise in
S GND 14
30k
V/I 2 9
Mono Multi. 4
L Rear In 15 L Frnt In 16
bias
AC GND 17 Diag 26 TAB 27 STNDBY 23 L Rear O24 L Frnt O+ 18 + L Frnt O20 Vp 1 21 Standby
Ad Sel 1
Terminal Description pin 1: Ad Sel pin 2: S DA pin 3: P GND 2 pin 4: R Rear Outpin 5: S CLK pin 6: R Rear Out+ pin 7: Vp2 pin 8: R Frnt Outpin 9: P GND 1 pin 10: R Frnt Out+ pin 11: SVR pin 12: R Front In pin pin pin pin pin pin pin pin pin 13: R Rear In 14: S GND 15: L Rear In 16: L Frnt In 17: AC GND 18: L Frnt Out+ 19: P GND 3 20: L Frnt Out21: Vp1
S CLK 5 R Rear O+ 6 Vp 2 7
S DA 2 P GND 2 3 R Rear O4
: I2C address select. : I2C data input/output. : Power ground. : Negaitve right rear output. : I2C clock input. : Positive right rear output. : Power supply. : Negaitve right front output. : Power ground. : Positive right front output. : Half supply filter capacitor. : Right front input. : Right rear input. : Signal ground. : Left rear input. : Left front input. : AC ground input. : Positive left front output. : Power ground. : Negaitve left front output. : Power supply. : Positive left rear output. : Standby operating selecting.
051-7525-08
P GND 4 25
SN74LVC2GU04DCKR
Dual Inverter
IN 1 1 GND 2 IN 2 3
6 OUT 1 5 VCC 4 OUT 2
051-7526-08
300
SN74LVC1G126DCKR
Single 3-States Buffer
OE 1 A2 GND 3
5 VCC 4Y
Truth table
OE in H L Y out =A High Z
pin 22: L Rear Out+ pin 23: STANDBY pin pin pin pin 24: L Rear Out25: P GND 4 26: Diag 27: TAB
: Negaitve left rear output. : Power ground. : Diagnose / clip detection output. : Heatsink connection, must be connected to ground.