PHILIPS PS1966C
Instrukcja Obsługi

TV AND REMOTE CONTROL OPERATION
TELEVISION
BEGIN

Press the POWER button to turn the TV ON.

Press the VOLUME + button to increase the sound level or the VOLUME � button to lower the sound level. Pressing both buttons at the same time will display the onscreen menu. Once in the menu, use these button to make adjustments or selections.
Remote Sensor Window

Press the CHANNEL UP v or DOWN w button to select TV channels.

Slide the TV/VCR/ACC mode switch on the remote control to the TV position and point the remote at the front of the TV when sending commands.

6

STEREO

Audio/Video Input Jacks (Stereo Audio Jacks)

MENU

INSTALL/ MENU

<

� VOLUME +

CHANNEL

POWER

VIDEO

L AUDIO R

<

<

� VOLUME +

CHANNEL

REMOTE
BATTERY INSTALLATION

POWER

VIDEO

L AUDIO R

1
Point the remote control toward the remote sensor window on the TV when operating the TV with the remote.

<

Headphone Jack

T

o load the supplied batteries into the remote:
ER POW CLOCK TV /VCR

2
CC

3

1. Remove the battery compartment lid on the back of the remote. 2. Place the batteries (2AA) in the remote. Be sure the (+) and (-) ends of the batteries line up correctly (inside of case is marked.) 3. Reattach the battery lid.

EP SLE A

ATUS/E /CH ST IRD REC CR

XIT

3
SMA RT P ICTU RE

TV V

ACC ART SM SOUND

SUR

F

M

ENU CH VOL
MUTE

4
Sleep Button
Press to set the TV to automatically turn itself OFF. Also can be used as an Enter button when sending channel commands to remote controlled cable converters or VCRs.
POWER SLEEP

Power Button
Press to turn the TV (or select VCR/ Cable Converter) ON and OFF.

CC Button
A/CH TV VCR RECORD STATUS/EXIT CC CLOCK

TV/VCR/ACC MODE SWITCH
The remote's TV/VCR/ACC Switch controls how buttons on the remote are used. For example: With the switch in the "TV" position: the Menu, CURSOR , , and s buttons are used to select and adjust onscreen TV features. With the switch in the "ACC" position: the Power, Channel Number, and Channel Up (+) /Down (�) buttons on the remote work with Cable TV Converters. With the switch in the "VCR" position: the Menu, CURSOR , , and s buttons on the remote work Stop, Play, and other VCR features. Note: For more details on how the TV remote works with VCRs and Cable Converters, see the other owner's manual supplied with your TV.

Status/Exit Button
Press to see the current channel number on the TV screen. Also press to clear the TV screen after control adjustments.

Press to select Closed Caption options within the menu. (Refer to the Owner�s Manual for details.)

TV/VCR

Clock-TV/VCR Button
When used in the TV mode, the CLOCK-TV/VCR button will access the Clock menu options. Press while in the VCR mode (VCR indicator on the front of the unit will light) to view the playback of a tape. Press again to place in the TV position (VCR indicator light will go off) to view one program while recording another program.

1 4 7
SMART SOUND

2 5 8 0

3 6 9
SMART PICTURE

A/CH-Record Button
Press to toggle between the currently viewed channel and the previously viewed channel. When in the VCR mode, press to start the recording of a video tape.

ACC

TV/VCR/ACC Mode Switch
Slide to TV position to control TV functions; VCR to control VCR functions; and ACC for Cable Converter, DBS, DVD, etc. functions.
MENU

SURF

Number Buttons
Press the number buttons to select TV channels. When selecting single digit channels, press the number of the desired channel. The TV will pause for a few seconds then tune to the selected channel. (Note: you can press "0", then the number also.) For channels "100" and above, first press "1" then the next two numbers of the desired channel.

SmartSound� Button
Press to select from a list of SmartSound controls. (Factory preset sound control levels set for different types of listening, based on the type of programming being used.)

Menu Button
Press for the onscreen menu to appear. Pressing the menu button after menu selections are made will eliminate the menu from the display.
VOL
MUTE

CH

SmartPicture� Button
Press to select from a list of SmartPicture controls. (Factory preset picture control levels set for different types of viewing sources and programs.) Press to select previously viewed channels. You can place up to 8 channels in memory. Then by pressing the SURF button you can quickly view the select channels. See the �Surf" section (in your other owner's manual) to see how to select a series of channels using the Surf button. When in the VCR mode, pressing this button will pause the playback of a video tape.

Cursor Buttons
Use these buttons to select and adjust the TV's onscreen menu. Also used with a VCR for PLAY, FAST FORWARD, REWIND, and STOP.

Surf Button

Volume (+), (�) Buttons
Press to adjust the TV sound level.

Mute Button
Press to turn the sound OFF on the TV. Press again to return the sound to its previous level.

Channel (+), (�) Buttons
Press to change the tuned channel.

SMART HELP
Remember, You can press any button on the front of the TV to turn the TV ON. Q/U-2 The tuned channel number will always briefly appear when the TV is first turned ON (and with channel changes.) You can also press the STATUS/EXIT button (on the remote) to see what channel the TV is ON.