JVC QL-F6
Instrukcja Serwisowa

2. HQ DAMPING knob This controls the horizontal movement of the tonearm while aiding to keep the tonearm s resonating

9. REPEAT knob
Decide how many times you want to re- listen to the record by using this knob. When you set the knob to " , the record will continue to play repeatedly.
Note: This knob cannot be

point low. Set the knob to the same indication number as the optimum tracking force of this unit.

turned to indicate from

3. VQ DAMPING knob
This controls the vertical movement of the tonearm while aiding to keep the tonearm s resonating point low. Set the knob to the same indication number as
4.

1 - 0 or 0 - 1

if the START button is de-

pressed with the power cord disconnected from the outlet. For this , refer to the note
in the section " Necessary
to record playing "

the optimum tracking force of this unit. Speed select knob

procedures prior on page 2.

Select a proper position of the speed select knob in accordance with the rpm of the record. 33- 1/3 rpm record (LP) 33" 45rpmrecord(EP)............. 45" 5. QUARTZ LOCK/PITCH CONTROL select button
QUARTZ LOCK:

10. START/REJECT buttons When you start playing a record , depress the ST ART button. The tonearm moves automatically

Depress the button to the QUARTZ LOCK position
) for playing a record at an accurate rotation

the position of the first groove of the record preselected and gently lowers itself onto the surface of the record to play it. When you stop playing the record , depress the REJECT button. The tonearm lifts , returns automatically to its rest and the platter
stops rotating. , however , the REPEAT knob has been set for a number of repeats, the tonearm performs the cor-

speed in the quartz lock mode. In this case ,
meter lights green. PITCH CONTROL:
Depress the button a second time to obtain

the

the

P ITCH CO NT RO L position (---) in order to perform fine pitch adjustment for the sound meeting

respond ing number of prepeats before the platter stops rotating. Note: When the dial of the repeat knob has been

set to numbers other than "
continues to rotate and the

, the platter

your preference. I n this case, the meter I ights orange.

6. PITCH CONTROL meter When the QUARTZ LOCK/PITCH CONTROL
select button is set to the QUARTZ LOCK position
the meter is green- lit and the indicator displays "

be turned off even though

power will not you depress the
has

REJECT button or even if the playing record has finished. When you want the
power to be turned off after the record
played once , be sure to the " 0" mark.

When the QUARTZ LOCK/PITCH CONTROL select button is set to the PITCH CONTROL position , pitch control can be performed by turning the PITCH CONTROL knob and the meter is
orange- I it.
#6 % means +6 % b6 % means - 6 %

to set the repeat knob

11. RECORD SIZE select knob
Set the knob to the corresponding position to the

size of the record before you play it. 30 cm diameter record. . . . 25 cm diameter record. . . .

30" (12"
25" (10"

7. PITCH CONTROL knob

17cmdiameterrecord...... " 17"(7")
12. Arm lifter lever

Fine pitch control

can be performed with the

QUARTZ LOCK/PITCH CONTROL select button
set to the PITCH CONTROL position. Pitch adjustment range is :!: 6 %. The indicator in the meter deflecting to the left (#) from the center (0) indicates an increase to the accurate 33- 1/3 or 45 rpm and the deflection to the right (b) means a decrease. 8. ANTI-SKATING knob
This device cancels out the

This is used

when you want to raise the tonearm

gently or gently lower it. When you push it to the UP" position , the tonearm will be lifted up, and when you pull it to the " DOWN" position , it will be lowered down gently onto the record surface.

centripetal force that
eliminates

pulls the tonearm to the center of the platter. This

prevents the stylus tip from skating toward the
center of the platter and at the same time
any excessive stylus tip force on the inner wall of

the record groove. Use the 8 marked dial when employing a spherical stylus. Use the marked dial when employing an elliptical stylus or a SHIBATA stylus. Turn the dial to the same number as on the track ing force dial.

QL-

No. 2464