|
|
|
Kto jest w sklepie?
Sklep przegląda 5695 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Schematy są ale można wysilić się i zrobić kolorowy skan i o większej rozdzielczości. Wtedy schematy płytek będą czytelniejsze. Całość super jako wartość merytoryczna. Wszystkie dane potrzebne do podłączenia różnego rodzajów urządzeń takich gramofon, CD itd.
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
FIGURE 8
Completed R.A.B.O.S. template
What Does a Parametric Equalizer Do? The R.A.B.O.S. system uses one band of parametric equalization for response correction. Parametric equalizers are the most versatile class of filters. The effect an equalizer will have on the signal is dependent on three parameters: Frequency: The equalizer will have maximum effect at one frequency, usually described as the center frequency. Level: This refers to the amount of cut (in dBs) the equalizer is set for.
Frequency The frequency of the R.A.B.O.S. equalizer may be adjusted to any one of nineteen frequencies from 20Hz to 80Hz.This determines where you are going to apply equalization.
NOTE: Positions 1�3 will all be at 20Hz. CCW: Fully Counterclockwise CW: Fully Clockwise
FIGURE 10
Effect of adjustable width
Now connect the dots as shown in Figure 9.This will make interpretation of the data much easier.
FIGURE 9
Test example with dots connected
Bandwidth: Defines the range of frequencies over which the equalizer will have an effect.This adjustment is abbreviated as �Width.� Only parametric equalizers allow independent adjustment of all three parameters. These will be explained more fully in the sections that follow. Completing the Measurement Template Along the bottom of the Measurement Template are three fields where you will enter the equalizer settings needed to complete system optimization. These instructions are based on the example in Figure 9. Use this tutorial to become familiar with the process. Strategies for several other test results will be presented later. After you have completed these three entry fields, you will be ready to perform the adjustments, completing R.A.B.O.S. optimization.
In this example, the highest level recorded is at 43Hz. This will be the frequency of the equalizer. Write 43 in the space provided. Width The frequency range of the R.A.B.O.S. equalizer may be set from 5% to 50% of an octave in 21 steps.This setting defines how much of the subwoofers� output will be equalized. Width is expressed as a percentage of an octave. For example, a width setting of 25% means the equalizer will affect a frequency band of 1/4 of an octave: 1/8 of an octave above and 1/8 of an octave below the center frequency. The octave is a logarithmic expression. From any point in the spectrum, one octave above or below that point is always double or half the frequency.Therefore, one octave above 100Hz would be 200Hz. One octave below 100Hz is 50Hz. In the section that follows, we will discuss the use of the Width Selector.
10
11
|
|
|
> |
|
