INSTALLATION
LOCATION If possible, place your model out of direct sunlight and away from heat sources suchas a radiator, oven, or range, Your model should not be installed where the temperature will go below 55°F. because it will not run frequently enough to maintain proper temperatures in the freezer, For ease of installation, you should leave a space of about one-half inch between your refrigerator and adjacent walls or cabinets, tf a wall prevents either door from opening at least 90 °, move the cabinet sideways an inch or so to permit a 900 opening so baskets and crispers can be easily removed. LEVELING IS IMPORTANT A refrigerator will not operate properly unless it is _evel and rests firmly on all four comers. Your model has four wheels and a leveling screw beneath each front corner at the base of the cabinet that can be turne/:lin or out as required, If the floor is not level and it is necessary to raise the rear of the cabinet, we suggest rollihg the rear wheels on to a piece of plywood or other shim material. Be sure that the two front levelers touch the floor to lock the cabinet in place.
J I
against possible electrical shock hazards. It must be plugged into a grounding receptaciR. Where a standard two prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded three-prong walt receptacle. DO NOT, under any circumstances, cut or remove the third (ground) prong from the power cord. 00 NOT use an adapter plug. All U.L. listed refrigeratorsend freezers are equipped with this type plug. SAFETY REMINDER
WARM
CABINET
SURFACES
At times, the front surfaces of your refrigerator cabinet may be warm to the touch. This is a normal function of your refrigerator. This feature prevents moisture from condensing on the outside of your refrigerator during humid weather. This condition may be noticeable when you first start your refrigerator, during hot weather, and excessive or lengthy door openings.
FEATURES The fresh food compartment is cooled by a gentle stream of circulating chilledair. To maintain the natural flavor, moisture and nutrition of fresh foods, we recommend that you cover open food containers. Dishes or trays containing left-overs should also be covered to seal in flavors. Storing tight store wrappings or in their original air foods in plastic bags reduces the evaporalion of moisture from them and lengthens storage time. SHELVES THE FREEZERSHELF can be removed by (1) lifting the quick-freeze compartment straight up until the left end bars of the freezer shelf are out of the sockets in the side wall of the quick-freeze compartment. (2) Lift the freezer shelf slightly and (3) pull to the left until right end bars are out of the sockets in the right freezer well. Reverse the removal procedure to replace the freezer shelf.
If you are not going to use your old refrigerator, be sure to REMOVE THE DOORS so a child won't be accidentally trapped inside and suffocate. This is required bylawin many communities,
OPERATION
SII: ! ! INO CONTROLS Your new refrigerator has two controls. One for regulating the temperature in the fresh food compartment and one for the freezer. The fresh food compartment and the freezer compartment controls are located at the' top front of the fresh food compartment. Turn both controls to "No. 5" to start your refrigerator,
The No. 9 freezer control setting ommended for short term use only. ELECTRICAL CONNECTION AND GROUNDING This appfiance is designed to operate on a nominal 115 volt, 15 amp., 60 cycle line. There should be a separate, grounded circult, serving this appliance only. DO NOT use an extension cord.
is rec-
Your refrigerator may run for several hours when you first start it. This is normal and shouldn't because for alarm, In a day or two, you may decide that one or both compartments should be colder or warmer, if so, ad,iusfthe controlls) as instructed in the accompanying chart, �
To stact 5e_ _re,_ _OOd cont,OI _ ,.5 ,.
can be removed and put in a lower position on the side wall. The freezer shelf can also be lowered into another position. ADJUSTABLE CANTILEVER SHELVES can be moved up or down to suit your individual needs. To remove a shelf, lift the front of the shelf straight up, rock slightly and pull straight out. To lock in another position, tilt shelf with the front up. Insert hooks into the desired frame openings and let the shelf settle into place. Make sure it is securely locked at the rear.
-
G_OUN_N
s
PLUG" _.1 I)
_flrt_
P_talOt
too
WARM
Turn
¢,esn fooa
co_t.oI
to ne,I
_#fFl_,_tGv"
t_
_,_LO
............. lower trttSh t_er TLzfn nUm fno_ ru,n _reeze,
COntrOl
IO _KI
co_t,ol
_o ne_t on "_" _'='_ I[_II i
pOWERwITH SUPPLYa_ PRoN_CORe
/
i
\
_teE.ZO¢ tO O _V_R M
_ ,_h I,eeze, sel _=¢number co_l,o_
GROUN01NG
TYPE
WALL RECEPTACLE -_oc,l,o_ o_,.o,._s oN,ow_.co,o ,LUG _,,__ O._e_ O_'YOU.'_OO_ ,.,_ s.o,_,,,e,_. This appliance is equipped with a threepronged grounding plug for your protection
USE OF CONTROLS IMPORTANT: EXCEPT WHEN STARTING, DO NOT CHANGE. EITHER CONTROL MORE THAN ONE NUMBER AT A TIME. ALLOW 24 HOURS FOR TEMPERATURE TO STABILIZE BEFORE RESI=I IING.
The meat keeper, between the top and second shelves, provides short term SlOtage of fresh meats. It slides OUt to the front so you can easily reach all items stored within. The meat keeper will provide extra chilling if the cantilver shelf that sup_ only :_ortsthe meat keeper is in the 2nd, 3rd, or 4tb shelf adjustment positions.
