JVC RX-8040BUD
Instrukcja Obsługi

Selecting different sources for picture and sound
While watching pictures from a video source (DVD player, VCR, or DBS tuner), you can listen to sound of an audio source. � Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source. Press one of the audio source selection buttons�PHONO, CD, TAPE/MD, CDR, FM, AM�while viewing the picture from a video component such as the VCR or DVD player, etc.
DVD VCR 1
PHONO CD CDR TAPE/MD FM AM

DVD MULTI VCR 2 VIDEO

PHONO TAPE/MD FM

CD CDR AM

TV/DBS

To use the speakers connected to the FRONT1 SPEAKERS terminals, press SPEAKERS ON/OFF 1 so that the SPEAKERS 1 indicator lights up on the display. � Make sure that the SPEAKERS 2 indicator is not lit. To use the speakers connected to the FRONT2/ZONE2 SPEAKERS terminals, press SPEAKERS ON/OFF 2/ZONE 2 so that the SPEAKERS 2 indicator lights up on the display. � Make sure that the SPEAKERS 1 indicator is not lit. To use both sets of the speakers connected to the FRONT1 SPEAKERS and FRONT2/ZONE2 SPEAKERS terminals, press SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2/ZONE 2 so that the SPEAKERS 1/2 indicators light up on the display.
ANALOG

On the front panel

On the remote

Adjusting the Zone 1 Volume

L

R

LINEAR PCM
SPEAKERS 1 2 VOLUME

ZONE 1

Ex. When both sets of the speakers selected.

Note: On the front panel: To increase the volume, turn MASTER VOLUME clockwise. To decrease the volume, turn it counterclockwise. On the remote control:
To increase the volume, press VOLUME +. To decrease the volume, press VOLUME �.
When you select DVD MULTI as the source or any one of the Surround/DSP mode which activates the center and/or surround speaker(s), you can use only one set of the speakers.

Notes:
� The volume level can be adjusted within the range of �0� (minimum) to �70� (maximum). � If you set �ONE TOUCH OPE� (One Touch Operation) to �ON� (see page 38), you do not have to adjust the volume level each time you change the source. It is automatically set to the stored level. � If you have turned off the receiver with the volume level set at more than level �30,� the volume level will be automatically set at level �30� next time you turn on the receiver.

To use neither set of the speakers connected to the FRONT1 SPEAKERS and FRONT2/ZONE2 SPEAKERS terminals, press SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2/ZONE 2 so that the SPEAKERS 1/2 indicators go off from the display. � Activating the speakers turns on the Surround and DSP modes previously selected.

Listening with headphones only: Connect headphones to the PHONES jack, and deactivate both sets of the front speakers so that �HEADPHONE� appears and the
HEADPHONE indicator lights up on the display.

� You can listen to left and right channel sound with headphones. � Make sure that all the speaker indicators are not lit.
You can enjoy the sound effects through the headphones when Surround or DSP mode is activated�3D Headphone (3D H PHONE) mode. � �3D H PHONE� appears and the DSP and HEADPHONE indicators light up on the display. (For details, see pages 47 and 48.)

CAUTIONS:
� Always set the volume to the minimum before starting any source. If the volume is set at a high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers. � Be careful not to turn up the volume too high when controlling the receiver without listening to the playback sound. For example, when adjusting the volume level in Zone 2 from Zone 1.

Note:
3D Headphone (3D H PHONE) mode is not valid for DVD MULTI playback mode.

Activating the Zone 1 Front Speakers

Remote NOT

CAUTION:
Be sure to turn down the volume: � Before connecting or putting on headphones, as its high volume can damage both the headphones and your hearing. � Before turning on the speakers again, as its high volume may come out of the speakers.

When shipped from the factory, both pairs of the front speakers have been set to be used in Zone 1. � To use the speakers connected to the FRONT2/ZONE2 SPEAKERS terminals, set the speaker usage correctly. (See �Setting the Zone 2/Speakers 2� on page 38.) When you have connected two pairs of front speakers and placed them in Zone 1, you can select which to use.

21