PANASONIC RXD29
Instrukcja Obsługi

Recording
You can record radio broadcasts or CDs. Before recording � This unit is suitable for recording normal tapes, but it cannot record onto high and metal position tapes to their full potential and prior recordings will not be erased correctly. � The recording level is set automatically. � Take up the leader tape before proceeding. To stop recording Press [ / STOP/EJECT ]. (The CD does not stop.) To stop recording temporarily Press [ PAUSE ]. (The CD does not stop.) Press once again to resume recording. To record on the other side of the cassette Turn the cassette over and press [ ]. If the CD finishes before the cassette Recording continues. Press [ / STOP/EJECT ] to stop it. If the cassette finishes before the CD The CD continues playing. Press [ ] to stop it. Erase protection Side A Use a screwdriver or similar object to break out the tab. Tab for side B To re-record on a protected cassette Cover the hole with adhesive tape. Adhesive tape Tab for side A

Leader tape (Recording cannot be made.)

13

1

Press [ / STOP/EJECT ] to open the deck and load a cassette.
Close deck by hand.

Exposed tape facing upward

To erase a tape 1. Press [TAPE/OFF]. 2. Insert the cassette with the side to be erased facing towards you and the exposed tape facing up. 3. Press [ ]. [ PLAY ] is depressed at the same time.
�

Side to be recorded facing you

2

Select the source to be recorded.
When recording radio broadcasts Tune in the station. (Perform steps 1�3 of �Normal tuning� on page 6.) When recording CDs Insert the CD to be recorded. (Perform steps 1 and 2 of �Normal play� on page 7.) Press [CD / ] and then [ ] to switch to CD mode. If you want to record programmed tracks, program desired tracks before proceeding to step 3.

3

Press [

] to start recording.

[ PLAY ] is also depressed with [ ]. Recording starts (one side only). The CD also starts playing if in CD mode.

Setting the time
3
2·4
� �

Press [� / time.
� � � � � � �

] or [

/ +] to set the

Press and hold to change the time faster.

Remote control only

3
This is a 12-hour clock.

4

Press [CLOCK/TIMER ADJ].

1
� �

Press [TUNER/BAND �AUTO PRESET] to turn the unit on.
You can also use [CD
� � � � � � � � � � �

To switch to clock display Press [DISPLAY]. Clock display � Current display � Displaying the clock temporarily Press [CLOCK/TIMER ADJ]. The clock is shown for about 10 seconds. Note The clock is accurate to within ± 60 seconds a month. Readjust if necessary.

/
�

], [
� �

PLAY] to turn the unit on.
� � � � � � � � � � � � � � � �

Remote control only

2

Press [CLOCK/TIMER ADJ] once.

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

1

�

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

� �

Note � Noise may be recorded if this unit is near a TV. Keep the units at least 1.5 meters apart. � Changes to volume and sound quality do not affect recording. � To prevent interruptions to recording, make sure there is constant AC power supply to the unit or replace the batteries. � While recording you cannot perform the following operations. - Switching play of the source (CD, Radio, Tape) - Switching the radio AM/FM frequency - CD skipping, searching

Within 10 seconds

9
RQTT0585