CASIO SPF40-1
Instrukcja Obsługi

2273-4
Countdown Mode Beeper Operations
The watch beeps at various times during a countdown to keep you informed about the countdown status without looking at the display. The following describes the types of beeper operations the watch performs during a countdown.

Countdown/Stopwatch Graphics
Graphic indicators move in a counter-clockwise direction during countdown timer operation and clockwise during stopwatch operation. � The zero point for both the minute�s indicator and the second�s indicator is the 12 o�clock position. � The factory default setting is graphics turned off.

Countdown End Beeper
The watch beeps each second of the final 10 seconds before a countdown reaches zero, and at zero. The first five beeps (seconds 10 through 6) are higher pitched than the final five beeps (seconds 5 through 1). The watch emits a longer beep to signal when the countdown reaches zero. Note The countdown end beeper always sounds, regardless of the on/off status of the progress beeper.

Countdown Graphics
Second�s indicator

Progress Beeper
The term �progress beeper� actually includes two beepers: a reset time beeper and a reset period progress beeper.
Minute�s indicator

� During a countdown operation, the graphic indicators move counter-clockwise. � One revolution of the second�s indicator represents 10 seconds. � The minute�s indicator appears when the countdown time is 10 minutes or less. The minute�s indicator advances one step with each full revolution of the second�s indicator. One revolution of the minute�s indicator represents 10 minutes.

Note The reset time beeper and reset period progress beeper sound only while the progress beeper is turned on. � Reset Time Beeper The reset time beeper is similar to the countdown end beeper. When the progress beeper is turned on, the watch beeps each second of the final 10 seconds before the countdown reaches the reset time. � Reset Period Progress Beeper The reset period is the portion of the countdown between the reset time and zero. When the progress beeper is turned on, the watch emits fours short beeps at the top of each minute during the reset period. Example 1 Countdown Start Time: 10'00" Reset Time: 5'00" Progress Beeper: On

Stopwatch Graphics
Second�s indicator

� During a stopwatch elapsed time operation, the graphic indicators move clockwise. � One revolution of the second�s indicator represents 10 seconds. � The minute�s indicator advances one step with each full revolution of the second�s indicator. One revolution of the minute�s indicator represents 10 minutes.

Minute�s indicator

To turn timer graphics on and off
Reset Period
Reset Period Progress Beeper

1. In the Countdown Timer/Stopwatch Mode, hold down A until the time setting starts to flash, which indicates the setting screen. 2. Display the graphics on/off screen. � If you started from the Countdown Timer Mode, press D three times. � If you started from the Stopwatch Mode, press D once. 3. Press E to toggle the graphic display on (ON displayed) and off (OFF displayed). 4. After making the setting you want, press A to exit the setting screen.

Start Time 10'00"

Reset time 5'00" 4'00" 3'00" 2'00" 1'00" 0'00" Reset Time Beeper Countdown End Beeper

Example 2 Countdown Start Time: 10'00" Reset Time: 5'00" Progress Beeper: Off

Start Time 10'00"

Reset time 5'00" 0'00" Countdown End Beeper

Using Countdown Timer
The following procedure is explained assuming the countdown timer is configured with the following sample settings. Progress beeper: On Countdown Start Time: 10 minutes Reset Time: 5 minutes

To turn auto repeat/repeat and the progress beeper on and off
1. While in the Countdown Timer/Stopwatch Mode, hold down A until the time setting starts to flash, which indicates the setting screen. 2. Make sure the setting screen shows a countdown start time other than zero. � The next step will not work if the countdown start time setting is zero. If it is, use the procedure to change it to another value (see �To set the countdown start time and reset time�). 3. Press D twice to display the screen for making auto repeat, repeat, and progress beeper settings. 4. Each press of E cycles though the available settings as shown below. Auto repeat, Progress beeper on

To use the countdown timer
In the Countdown Timer/Stopwatch Mode, press E to start the countdown timer. � The indicator YACHT flashes on the display while a countdown operation is in progress. � The countdown proceeds in accordance with the configuration settings you made using the procedures under �Configuring the Countdown Timer�. The table below describes the button operations you can perform while a countdown operation is in progress.
To do this: Stop the countdown operation Display the reset time (5 minutes in this example) Do this: Press E. Press A. � Pressing E after displaying the reset time starts the countdown from the displayed time. Press A and E at the same time, or press A twice.

Auto repeat, Progress beeper off
Display the countdown start time

Repeat, Progress beeper on

Repeat, Progress beeper off 5. After making the setting you want, press A to exit the setting screen. Note Even if you turn the progress beeper off, the watch beeps every second for the last 10 seconds before the end of a countdown is reached.

The following describes the operations you can perform while the countdown operation is stopped (by pressing E).
To do this: Resume the countdown from the currently displayed time Display the countdown start time (10 minutes in this example) Do this: Press E. Press A and E at the same time or press A. � Pressing E after displaying the countdown start time starts the countdown from the displayed time.