JVC SP-X103AS
Instrukcja Obsługi

ENGLISH
I Types of speaker systems I CONNECTION
� Connect the LEFT speaker terminals of the amplifier to the terminals of the LEFT speaker and RIGHT to RIGHT and CENTER to CENTER using the attached speaker cords as shown in the figure making sure polarity is correct; (+) to (+) and (�) to (�). Connect the black speaker wire to the (�) terminal. � Turn off power to the whole system before connecting the speakers to the amplifier. � The nominal impedance of the SP-X103 is 8 �. Select for use an amplifier to which a speaker system with the load impedance of 8 � can be connected. � The maximum power handling capacity of the SP-X103 is 100 W. Excessive input will result in abnormal noise and possible damage. In cases where the signals described below are applied to the speakers, even if the signals are below the maximum allowable input, they may cause an overload and burn the wiring of the speakers. Be sure to lower the amplifier volume beforehand. 1) Noise during FM tuning. 2) High level signals containing high frequency components produced by a tape deck in the fast forward mode. 3) Click noise produced when turning power of other components on and off. 4) Click noise produced when connecting or disconnecting cords with the power on. 5) Click noise produced when the cartridge is replaced with the power on. 6) Click noise produced when operating amplifier switches. 7) Continuous high frequency oscillation or high pitch electronically produced musical instrument sound. 8) Howling when using a microphones.

Center speaker (1)

SP-X103C

Satellite speakers (4)

SP-X103F

I Precaution for when hanging the speaker system on walls and pillars
G Check and make sure that the walls and pillars are strong enough to enable the installation of the speaker system. If they are weak, it is imperative that you reinforce them. If walls or pillars with insufficient strength are employed, the speaker system may fall, resulting in injury and/or trouble. G Installing the provided wall hanging bracket. 1) Connect the speaker cord. 2) Install the provided wall hanging bracket onto the speaker body with the screw that is also provided. 3) Adjust the angle of the speaker body. 4) Use the hole of wall hanging bracket and hang it on a nail or a wooden screw of the wall.
Screw (not provided) Speaker body

I SPEAKER FOR A/V COMBINATION
SP-X103 have a magnetically-shielded design for placement adjacent to TVs and monitors without causing color aberrations. However, color may be affected as a result of how the speaker system is installed. Therefore, be careful of the following: 1. When placing these speakers near a TV set, turn off the TV�s main power switch or unplug it before installing the speakers. Wait at least 30 minutes after the system is installed before turning on the TV�s power. 2. If another speaker system has been set up near the TV set, that system may cause color unevenness in the TV�s picture. 3. In spite of the shielded design of these speakers, some types of TV�s may be affected by them. If this happens, move the speakers a short distance form the TV set.

Wall hanging bracket Screw (M5 � 10 mm) (provided)

You can adjust the angle by loosening the screw. Tighten the screw after adjusting the angle.

I CONNECTION
1. If cords are covered with insulation, twist the core of the cord at the end of each cord,then remove the insulation.

I SPECIFICATIONS
Type 2. Insert it into the hole while pressing down the terminal lever.
Black Press

Speakers Power Handling Capacity Impedance Frequency Range Sound Pressure Level Dimensions (W � H � D) Satellite speakers Center speaker Mass Accessories

: 1-way 2-speaker Bass-Reflex Type (Magnetically-shielded type) : 5.5 cm cone � 2 : 100 W : 8� : 80 Hz � 20 000 Hz : 81 dB/W·m : : : : 82 mm � 159 mm � 111 mm 158 mm � 87 mm � 111 mm 0.77 kg each Speaker cord (10 m) .................................. 2 (5 m) .................................... 3 Bracket ................................ 2 Screw (M5 � 10 mm) ........... 2

Center speaker Satellite (Front, right) Satellite (Front, left)

SP-X103C

SP-X103F
Speaker terminals on the amplifier

SP-X103F

SP-X103F
Satellite (Surround, right)

SP-X103F
Satellite (Surround, left)

�2�