|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
- GENERAL
- TEST MODE
- DIAGRAMS
- Circuit Boards Location
- Block Diagrams
- Main Section
- Power Section
- Printed Wiring Board - Digital Section
- Schematic Diagram - Digital Section
- Printed Wiring Board - Main Section
- Schematic Diagram - Main (1/3) Section
- Schematic Diagram - Main (2/3) Section
- Schematic Diagram - Main (3/3) Section
- Printed Wiring Board - Display Section
- Schematic Diagram - Display Section
- Printed Wiring Board - Video/Key Section
- Schematic Diagram - Video/Key Section
- Printed Wiring Board - Power Supply Section
- IC Pin Function Description
- IC Block Diagrams
- EXPLODED VIEWS
- Front Panel Section
- Chassis Section
- ELECTRICAL PARTS LIST
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
z About speaker distances
This receiver allows you to input the speaker position in terms of distance. However, it is not possible to set the center speaker farther away than the front speakers. Also, the center speaker can not be set more that 5 feet (1.5 meters) closer than the front speakers. Likewise, the rear speakers cannot be set farther away from the listening position than the front speakers. And they can be no more than 15 feet (4.5 meters) closer. This is because incorrect speaker placement is not conducive to enjoy the surround sound. Please note that, setting the speaker distance closer than the actual location of the speakers will cause a delay in the output of the sound from that speaker. In other words, the speaker will sound like it is farther away. For example, setting the center speaker distance 3~6 feet (1~2 m) closer than the actual speaker position will create a fairly realistic sensation of being �inside� the screen. If you cannot obtain a satisfactory surround effect because the rear speakers are too close, setting the rear speaker distance closer (shorter) than the actual distance will create a larger soundstage. (1 foot corresponds to a 1 ms difference.) Adjusting these parameters while listening to the sound often results in much better surround sound. Give it a try!
Adjusting the speaker volume
Use the remote while seated in your listening position to adjust the volume of each speaker. Note
This receiver incorporates a new test tone with a frequency centered at 800 Hz for easier speaker volume adjustment.
Hooking and Setting Up the Speaker System
1 2
Press ?/1 to turn on the receiver. Press TEST TONE on the supplied remote. You will hear the test tone from each speaker in sequence. Adjust the volume level so that the volume of the test tone from each speaker sounds the same when you are in your main listening position. � To adjust the balance of the front right and front left speakers, use the front balance parameter in the LEVEL menu (see page 34). � To adjust the balance of the rear right and rear left speakers, use the rear balance parameter in the LEVEL menu (see page 34). � To adjust the volume level of the center speaker, press MENU </> to select the center parameter. Use +/� on the remote to adjust the level. � To adjust the volume level of the rear speaker, press MENU </> to select the rear parameter. Use +/� on the remote to adjust the level.
3
4
Press TEST TONE on the remote again to turn off the test tone.
Note
The test tone cannot be output when the receiver is set to 5.1CH INPUT.
z You can adjust the volume level of all speakers at the same
time
Rotate MASTER VOLUME on the receiver or press MASTER VOL +/� on the remote.
19
|
|
|
> |
|
