|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
...instruction is ok.
...instrukcja jest ok.
Thanks/Dzięki
;
Documentation made available quickly and It is good quality. Thanks.
TK-3148
ADJUSTMENT / ��
Repair Jig (Chassis)
Use jig (part No.: A-10-4060-04) for repairing the TK-3148. Place the TX-RX unit on the jig and fit it with screws. The jig facilitates the voltage check and protects the module when the voltage on the flow side of the TX-RX unit is checked during repairs.
维修����壳�
使ç�¨æ�ºå£³ï¼�A-10-4060-04ï¼�ç»´ä¿® TK-3148ã��å°� TX-RX å��å��æ�¾ç½® å�¨æ�ºå£³ä¸�ï¼�并ä¸�æ�§ä¸�è�ºé��ã�� å�¨ç»´ä¿®è¿�ç¨�ä¸ï¼� å½�é��è¦�å�¨TX-RXå��å��ç��ç�µè·¯æ�¿ä¸�æ£�æµ�å�°ç�µå�� æ�¶ï¼�æ�ºå£³å�¯ä»¥æ�¹ä¾¿å�°è¿�è¡�ç�µå��æ£�æµ�ï¼�并ä¸�ä¿�æ�¤æ¨¡å��ã��
Battery Jig (W05-0909-00)
ç�µæ± 夹å�·ï¼�W05-0909-00ï¼�
+ Terminal (Red) ï¼�æ��端å�(红è�²) â�� Terminal (Black) ï¼�æ��端å�(é»�è�²)
Connect the power cable properly between the battery jig installed in the transceiver and the power supply, and be sure output voltage and the power supply polarity prior to switching the power supply ON, otherwise over voltage and reverse connection may damage the transceiver, or the power supply or both. Note: When using the battery jig, you must measure the voltage at the terminals of the battery jig. Otherwise, a slight voltage drop may occur within the power cable, between the power supply and the battery jig, especially while the transceiver transmits.
å�¨å®�è£�äº�ç�µæ± 夹å�·ç��æ� 线ç�µæ�¶å��æ�ºå��ç�µæº�ä¹�é�´è¿�æ�¥ç�µæº�ç�µ ç¼�ï¼�并确认è¾�å�ºç�µå��å��两æ��æ�¥é��å��ç�µæº�æ�¯å�¦ç¡®å®�æ�¥é��ï¼�å�¦å��è¿� é«�ç�µå��å��ç�µæ��è¿�æ�¥é¢ å��é�½æ��å�¯è�½æ��å��æ� 线ç�µæ�¶å��æ�ºæ��ç�µæº�æ��é�½ 被æ��å��ã��
注: å½�使ç�¨ç�µæ± 夹å�·æ�¶ï¼�ä½ å¿�é¡»æµ�è¯�ç�µæ± 夹å�·ç��两个ç�µæ��ç��ç�µ å��ã��å�¦å��å½�æ� 线ç�µæ�¶å��æ�ºæ�¶å��ä¿¡æ�¶ï¼�å�¨ç�µæº�å��ç�µæ± 夹å�·ä¹�é�´ç�� ç�µç¼�线ä¸�ä¼�å��ç��å¾®å°�ç��ç�µå��é��ã��
How to Remove the Cable
1. Gently draw out both sides of the connector lever uniformly in the direction of the arrow with tweezers. (CN303, CN304, CN305, CN306)
������
1ï¼� æ��ç�§ç®å¤´æ��示ç��æ�¹å��ï¼� ç�¨é��å�å��å��å�°å°�è¿�æ�¥å�¨æ�¨æ��ç��两侧æ©� å¼�ã�� ï¼�CN303, CN304, CN305, CN306ï¼�
Tweezers é��å�
2. Gently rise up the connector lever in the direction of the arrow with a fine regular screwdriver or tweezers. (CN301, CN302, CN400)
Regular screwdriver 常����
2ï¼� 使ç�¨å¸¸ç�¨ç��å°�å��æ�¹é�¥ï¼� æ��ç�§ç®å¤´æ��示ç��æ�¹å��å°�å¿�å�°æ�¬èµ·è¿�æ�¥ å�¨ç��æ�¨æ��ã�� ï¼�CN301, CN302, CN400ï¼�
Flat cable �平�� Lever ��
38
|
|
|
> |
|
