JVC TM-H1750CG/E
Instrukcja Obsługi

PREPARATION
INSTALLING THE INPUT CARD
1. Turn off the Color Video Monitor�s main power and unplug the power cable from the AC outlet. 2. Unscrew the screws and remove the slot cover from the slot (on the rear side of the monitor) in which you are going to install the card.
SLOT

HOW TO HANDLE BASIC OPERATIONS
BASIC OPERATION
1. Press the main power switch to turn on the power. 2. Press the POWER switch to turn on the power.
POWER
STATUS indication (PAL or NTSC)
PAL

Rear side of the TM-H1750CG color video monitor
REMOTE

ON : Power turns ON. (Power indicator: lit) Green : The main power is ON, and the monitor�s power is ON (in the normal operation mode). OFF : Power turns OFF. (Power indicator: unlit) Orange : The main power is ON, but the monitor�s power is OFF (in the standby mode) Unlit : The main power is OFF.
About the STATUS indication � With the COLOR SYSTEM setting set to AUTO mode, when you turn on the power or select inputs, the color system indication appears for about 3 seconds on the screen while PAL or NTSC signals are being detected. It does not appear when receiving a B/W signal or when no signal is input. Refer to page 11 for more information about COLOR SYSTEM setting and page 12 for more information about STATUS indication setting.

SLOT

3. Press the INPUT SELECT buttons to choose input.
Select video/audio signals input to terminals on the rear panel. The selected button lights in green.
Slot cover
A B C SLOT D

VIDEO A

INPUT SELECT
OUT

IN

VIDEO B
IN OUT

INPUT SELECT buttons 1 Input A (VIDEO)

Terminals on the rear panel Video signal input VIDEO A terminal VIDEO B terminal Audio signal input AUDIO A terminal

IN

Y/C

(VIDEO/Y/C)

3. Insert the Input Card�s board (green-colored) into the slot, fitting the board into the guide rails on the top and bottom of the slot.
Fit the board to the guide rails. Knob
REMOTE

3 Input C 4 Input D

AUDIO B terminal VIDEO B (Y/C) terminal Refer to page 7 for details about the input terminals on each card and the INPUT SELECT button.

Note: The Y/C (S-video) terminal has priority.

00 ~ 50

4. Press the VOLUME/SELECT buttons to adjust the speaker volume.
VOLUME/SELECT

Press this button to display the speaker volume level on the screen. + : The Built-in speaker volume is increased. (00 = 50) � : The Built-in speaker volume is decreased. (50 = 00)
* Screen indication will disappear about 10 seconds after operating. * The on-screen display goes off when you press MENU button.

SLOT

VOLUME

:

20

�

+
UPPER

VIDEO A

Guide rails
OUT OUT

PICTURE ADJUSTMENT
1. Press select buttons corresponding to the item you want to adjust.
CHROMA CONTRAST PHASE BRIGHT

IN

VIDEO B

IN

IN

Y/C

Knob

Input card (the illustration shown is of the IF-C01COMG)

�40 ~ +40
PHASE : 00

4. Push the Input Card in so that its front panel touches the monitor�s rear panel. 5. Secure the Input Card by replacing the screws removed in Procedure 2.

The item you select is displayed on the screen. 1 Chorma control : Press the CHROMA/PHASE button once. 2 Phase control : Press the CHROMA/PHASE button twice. 3 Contrast control : Press the CONTRAST/BRIGHT button once. 4 Brightness control : Press the CONTRAST/BRIGHT button twice.
* Pressing the CHROMA/PHASE button and CONTRAST/BRIGHT button alternately while the item is shown on screen restores the previous status. When no item is shown on screen, CHROMA and CONTRAST have priority.

PHASE

:

00

2. Adjust with the VOLUME/SELECT buttons.
REMOTE

Notes:

�

LOWER

+

VOLUME/SELECT

Items CHROMA (Chroma)

VOLUME/SELECT button � + lighter reddish lower darker deeper greenish higher brighter

� Phase control is effective only in the NTSC color system mode. � Chroma control is not effective when receiving RGB and B/W or when no signal is input. (Except when a component signal is input.) � When CHROMA is adjusted to ��40,� the picture becomes less colorful. � �NO EFFECT� is displayed (for about 3 seconds) when your selected function has no effect. � To change the display position on screen, set UPPER or LOWER with ADJ. BAR POSI.

VIDEO A

IN

OUT

VIDEO B

IN

OUT

PHASE (Phase) CONTRAST (Contrast)

IN

Y/C

NOTE : Do not touch the terminal connected to the monitor or board pattern. Do not remove slot covers from the monitor�s slots if they are not in use.

BRIGHT (Brightness)

ENGLISH

2 Input B

No.51923 1-5
8

TM-H1750CG

* Screen indication will disappear about 10 seconds after operating. * The on-screen display goes off when you press MENU button.

9