|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
TX-NR900/E ADJUSTMENT AND CONFIRMATION PROCEDURES 1
Idling current adjustment Before Idling current adjustment, turn the trimming resistors R6040 to R6046 to counter-clockwise. Connect the DC voltmeter at the sockets P6080 to P6086. After turn POWER to ON, adjust the trimming resistors R6040, R6041 and R6042 so that the reading of voltmeter becomes 11 mV. (Front and center channels) Adjust the trimming resistors R6043, R6044, R6045 and R6046 so that the reading of voltmeter becomes 4.5 mV. (Surround and surround back channels) After adjustment, attach the top cover. Confirm the voltage of points above after about five minutes. Front and center channels When less than 16.5 mV, readjust the resistors above so that the voltage becomes 16.5 mV. When 16.5 mV to 18.5 mV, you are not necessary to adjust. When more than 18.5 mV, readjust the resistors above so that the voltage becomes 18.5 mV. Surround and surround back channels When less than 6.0 mV, readjust the resistors above so that the voltage becomes 6.0 mV. When 6.0 mV to 8.0 mV, you are not necessary to adjust. When more than 6.0 mV, readjust the resistors above so that the voltage becomes 8.0 mV. Note: No load and No signal
R6040
P6080 IDID+ P6001
R6041
P6081 IDID+ P6011 P5003B
R6042
P6082 IDID+
P6000
P6010
P6002 P5003C
P6012
P5003A P6205
P5004A P6013 ID+ IDP6083
P5004B P6003 BIAS ID+
P6004 BIAS
P5004C P6015 BIAS R6045
P6005 P5004D P6016 ID+ ID-P6086 BIAS R6046
P6006
R6043
ID-
P6084
R6044
ID+ ID- P6085
NCAF-7706
Confirmation of protection circuit 1. Confirmation of operation of speaker relay Confirm that the speaker relays turn ON approximate. 5 seconds after the power switch is turned ON. Confirm that the speaker relays turn OFF immediately after the power switch is turned OFF. 2. Confirmation of DC detection circuit Press and hold down CD button, then press STANDBY/ON and DISPLAY buttons to set the unit to "Test-1" mode. After "Test-1" on the FL tube light on, press VIDEO 1 button to set the unit to "Test-1-00". Apply DC 1.5 to 3.5V to the MULTI-CH INPUT terminal with no load. Confirm that the speaker relay turns OFF. Apply DC -1.5 to -3.5 V to the MULTI-CH INPUT terminal with no load. Confirm that the speaker relay turns OFF. Caution: Don't apply DC voltage more than 1 sec..
|
|
|
> |
|
