PIONEER VSX-AX10AI-G/DLT
Instrukcja Obsługi

07

The Surround Setup menu

7 If you selected �Reverb View�, you can use the cursor buttons (hard keys) to check the reverb characteristics for each channel. Select �Return� and press ENTER when you�re done.
2.4. Acoustic Cal EQ Pro. Reverb View dB [C] [ 500Hz ]

X-Curve
Most soundtracks mixed for cinema sound too bright when played back in large rooms. The X-Curve setting acts as a kind of re-equalization for home theater listening, and restores proper tonal balance of movie soundtracks. 1 Select �X-Curve� then press ENTER.
2. Surround Setup
[ Check ] [ [ [ [ 1. 2. 3. 4. Speaker Systems ] Channel Level ] Speaker Distance ] Acoustic Cal EQ ]

0

80

160ms

[Return]

Use the / (cursor left/right) buttons to select the channel and the frequency you want to check. Use the / (cursor up/down) buttons to go back and forth between the two. Note that the markers on the vertical axis indicate decibels in 2dB steps. 8 If you selected �Advanced EQ Setup�, input the time setting you want to use for calibration, then select �Go�. Select �Start� from the next screen. Based on the reverb measurement above, you can manually choose the time period that will be used for the final frequency adjustment and calibration. Even though you can make this setting without reverb measurement, it is best to use the measurement results as a reference for your time setting. For an optimal system calibration based on the direct sound coming from the speakers, we recommend using the 20�40ms setting.
2.4. Acoustic Cal EQ Pro. dB [C] [ 500Hz ]

[ 5. X-Curve ] [ Return ]

2 Use the / (cursor left/right) hard keys to switch the X-Curve ON or OFF.
2. 5. X-Curve X-Curve [ Manual ] [ Semi Auto ] [ Return ] Your X-Curve " �0.5dB/oct " [ ON ]

If you select OFF, the frequency curve will be flat and you won�t be able to adjust the X-Curve.
1k

12

50

3

Select a setup option and press ENTER.
2. 5. X-Curve X-Curve [ ON ]

0

80

160ms

[ Manual ] [ Semi Auto ] [ Return ] Your X-Curve " �0.5dB/oct

[20~40ms] [Go] [Return]

4k

"

Use the / (cursor left/right) buttons to select the channel, frequency, and time setting. Use the / (cursor up/down) buttons to switch between them. You can switch between your connected speakers (excluding the subwoofer), and display the measurements for the following frequencies: 63Hz, 125 Hz, 250Hz, 500Hz, 1kHz, 2kHz, 4kHz, 8kHz and 16kHz. Select the setting from the following time periods (in milliseconds): 0�20ms, 10�30ms, 20�40ms, 30�50ms, 40�60ms, 50�70ms and 60�80ms. This setting will be applied to all channels during calibration. When you�re finished, select Go. It will take about 2�11 minutes for the calibration to finish. !! Complete !! is displayed on-screen after the acoustic calibration equalization is set. If you want to check the settings, select Check and press ENTER. If you want to finish, select Return to exit each screen.

� Manual � Adjust the X-Curve manually. � Semi Auto � The X-Curve is calculated automatically. The larger your listening area (as determined by the speaker distance setting), the greater the X-Curve slope (see the following step for more on this). 4 Check the X-Curve setting. If you selected �Manual�, make any adjustments necessary to the XCurve.
2.5. X-Curve Manual X-Curve [ �2.0dB/oct ]

63

25

2k

[ Return ]

64
En

8k 16