|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
The System Setup menu
09
Subwoofer setting
This option only appears if you have connected a subwoofer. Note that some subwoofer settings are not available depending on other speaker settings. Specifies the behavior of the subwoofer: � SUBWF 200 � Most of the bass frequencies are played through the subwoofer � SUBWF 150 � Mid setting � SUBWF 100 � Only the very lowest bass frequencies are played through the subwoofer � SUBWF ��� � No sound from the subwoofer � SUBWF PLS � For extra bass power Note � The SUBWF PLS setting is only available when the front speakers are set to FRONT L. � When all speakers are set to L, you cannot select the SUBWF 200, or SUBWF 150 settings. � If you set the front speakers to FRONT S, you cannot select the SUBWF ��� setting. � Depending on the source and other receiver settings, you may not always hear sound from the subwoofer.
Right-surround speaker distance setting
Specifies the distance from your listening position to the surround-right speaker: � RS 0.1 m. � RS 9.0 m. � Distance can be set in increments of 0.1 m. The default is 2.0 m.
Surround-back speaker distance setting
Specifies the distance from your listening position to the surround-back speaker: � SB 0.1 m. � SB 9.0 m. � Distance can be set in increments of 0.1 m. The default is 2.0 m.
Left-surround speaker distance setting
Specifies the distance from your listening position to the left-surround speaker: � LS 0.1 m. � LS 9.0 m. � Distance can be set in increments of 0.1 m. The default is 2.0 m.
Subwoofer distance setting
Specifies the distance from your listening position to the subwoofer: � SW 0.1 m. � SW 9.0 m. � Distance can be set in increments of 0.1 m. The default is 2.0 m.
LFE attenuator setting
Dolby Digital and DTS audio sources include ultra-low bass tones. Set the LFE attenuator as needed to prevent the ultra-low bass from distorting the sound. � LFEATT 0 � The LFE channel is played with no attenuation � LFEATT10 � LFE channel is attenuated by 10 dB � LFE OFF � LFE channel is not played
Dynamic Range Control
Specifies the amount of dynamic range adjustment to Dolby Digital or DTS soundtracks: � DRC OFF � No dynamic range adjustment (use when listening at higher volume) � DRC MAX � Dynamic range is reduced (loud sounds are reduced in volume while quieter sounds are increased) � DRC MID � Mid setting Note � This setting works only with Dolby Digital or DTS soundtracks. For other sources you can create a similar effect using the Midnight mode (see Using the Sound Modes on page 28).
Front-left speaker distance setting
Specifies the distance from your listening position to the front-left speaker: � L 0.1 m. � L 9.0 m. � Distance can be set in increments of 0.1 m. The default is 2.0 m.
Center speaker distance setting
Specifies the distance from your listening position to the center speaker: � C 0.1 m. � C 9.0 m. � Distance can be set in increments of 0.1 m. The default is 2.0 m.
Front-right speaker distance setting
Specifies the distance from your listening position to the front-right speaker: � R 0.1 m. � R 9.0 m. � Distance can be set in increments of 0.1 m. The default is 2.0 m.
35
En
|
|
|
> |
|
