Gruba instrukcja - poprostu wszystko co potrzreba - polecam .
Tekstowy podgląd strony 39 (kliknij aby zobaczyć)
Controlling the Rest of Your System
Erasing One of the Remote Control Button Settings
This erases one of the buttons you have programmed and restores the factory installed preset to that button. VSX-D710S/D810S:
2 Use the number buttons to enter 0123.
The LED light for half a second for each digit input. On the VSX-D710S and VSX-D810S the LED lights for two seconds to indicate that the setings have been restored to the factory presets. (If the LED blinks three times, then you made a mistake with the code�try re-entering it.) On the VSX-D850S the LCD displays 0123 and then �OK� for two seconds if the four digit code has been accepted. If any error has occurred display will blink three times.
1 Press SETUP and hold for three seconds.
The LED on the remote control will light for two seconds.
2 Press the MULTI CONTROL button relating to the function of the button to be cleared.
The remote control will return to the previous mode after thirty seconds of inactivity.
Direct Function
The direct function is a useful feature which allows you keep the receiver in one function (for example, CD) while putting the remote control in a different function. This could let you, for example, use the remote control to set up and listen to a CD on the receiver and then use the remote control to rewind a tape in your VCR while you continue to listen to your CD player. When the DIRECT function is ON any MULTI CONTROL button you press will change the function of both the receiver and the remote control. When you turn the DIRECT function OFF you can operate the , remote control without affecting the receiver. Thus you could switch the remote control the VCR and operate that component while the receiver plays a different component. To set a MULTI CONTROL button to DIRECT ON or DIRECT OFF:
3 Press the RECEIVER
The LED blinks.
button twice within
three seconds to start erase mode. 4 Press the button to be cleared for three seconds.
The LED lights steadily for three seconds and then goes off.
5 Repeat steps 4 to erase other codes. 6 Press and hold the SETUP button for one second to exit the erase mode.
VSX-D850S:
1 Press SETUP and hold for three seconds.
The LED on the remote control will light for two seconds and the display shows SETUP.
2 Use the @ # buttons to select the Erase mode.
The LCD display shows ERASE.
1 Press SETUP and hold for three seconds.
On the VSX-D710S and VSX-D810S the LED on the remote control will light for two seconds. On the VSX-D850S the LCD display SETUP icon will light. If you want to cancel the Direct Function mode, press
SETUP.
3 Press the MULTI CONTROL button relating to the function of the button to be cleared. 4 Press the button you want to clear. 5 Repeat steps 3-4 to erase other codes.
The remote control will also return to the previous mode after thirty seconds of inactivity.
2 Press the MULTI CONTROL button that you want to set up.
Clearing All the Remote Control Settings
Clears all presets, all learned functions and restores the factory presets.
3 Use the number buttons to enter 9990 (DIRECT ON) or 9995 (DIRECT OFF).
The LED will light for half a second on each digit input. Then, on the VSX-D710S and VSX-D810S the LED will light for two seconds to indicate that it�s been correctly set. (If the LED blinks three times, then you made a mistake with the code�try reentering it.) On the VSX-D850S, the LCD will display �OK� to show the four digit code has been accepted. If it hasn�t been accepted the display will blink three times. MEMO: � TV CONT doesn�t have this feature and thus can�t use the DIRECT FUNCTION.
1 Press SETUP and hold for three seconds.
For the VSX-D710S and VSX-D810S the LED on the remote control lights for two seconds. For the VSXD850S the SETUP icon lights. If you want to cancel the Clearing mode, press
SETUP.
The remote control will also return to the previous mode after thirty seconds of inactivity.
