5. Clean the CCD faceplate with care. Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton tipped applicator and ethanol. 6. Never face the camera towards the sun. Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused.
7. Do not operate the camera beyond the specified temperature, humidity or power source ratings. Use the camera under conditions where temperature is between �10 °C - +50 °C (14 °F 122 °F), and humidity is below 90 %. The input power source is AC 24 V. 8. Do not connect this camera during a lightning storm. Otherwise, electric shock may be caused.
AUTO: The camera selects black-and-white mode if the picture is dark, or color mode if the picture is bright enough. Notes: � When using this unit with a video servo control lens, you may not switch from the black-and-white mode to the color mode depending on lens iris. In such a case, operate the lens adjuster to open the aperture. � This function may not be activated automatically when a backlight or a strong light source causes excessive contrast in the picture. In such cases, use the Day/Night input terminals. !3 Duration Time Selector This selector is available when the Day/night
LOW: Color picture switches to black-andwhite pictures at approx. 5 lx with F1.2 lens. The factory default setting is HI. !5 Power Indicator (POWER) !6 Day/Night Input Terminal (DAY/NIGHT IN/GND) This terminal is used for connecting the camera to an external day/night detecting sensor. Terminals opened: color picture Terminals shortened: black-and-white picture !7 Video Output Cable with BNC Connector Connects the VIDEO IN connector of the monitor. !8 Power Cable
Caution for Mounting the Lens
The lens mount should be a C-mount or CS-mount (1�-32UN) and the lens weight should be less than 450 g (0.99 lbs). If the lens is heavier, both the lens and camera should be secured by using the supporter. The protrusion at the rear of the lens should be as shown below.
Day/Night Connections
Connect an optical sensor to the Day/Night Input terminals. � Day/Night Input terminals with a capacity of 5 V DC pull-up input, 0.2 mA or more. OFF: break contacts: color picture ON: make contacts: black-and-white picture Note: To activate the Day/Night function, set Day/Night Mode Selector to COLOR FIX.
Color CCTV Cameras
WV-C
P25
4H
Operating Instructions
Model No.
WV-CP254H
Caution: To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the AC 24 V Input Cable.
C-mount: Less than 13 mm (1/2�) CS-mount: Less than 8 mm (5/16�)
(Lens: Option)
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
switch position is 'AUTO'. Switching time (5 sec. or 1 minute ) is selectable. !4 BW Level Selector Selects the luminance level. This selector is available when the Day/night switch position is 'AUTO'. According to the luminance level, this camera automatically switches the condition of picture from color to black-and-white, or in reverse. HI: Color picture switches to black-and-white pictures at approx. 7 lx with F1.2 lens.
!7
N0703-1103 3TR001812BAA Printed in Japan
Cautions: 1. CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY. Be sure to connect the grounding lead to the GND terminal. 2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the Input Terminal. 3. The connections should comply with
FOCUS OR FLANGE-BACK ADJUSTMENT
1. Loosen the focus lock knob. 2. Adjust the focus lock knob to obtain a focused point while watching the monitor screen. 3. Tighten the focus lock knob.
WV-C C
!8
National Electrical Code (NEC).
For U.S.A
P2 54H
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
CONNECTIONS
q
INT BLC SHARP COLOR ON AGC VIDEO FIX HI HI ALC ATW1 1MIN
w
e
â� Connections
Caution: The following connections should be made by qualified service personnel or system installers in accordance with NEC 725-51.
Caution: Tightening the knob by force will cause damage to the knob or deviation of focus. Note: The object may be out of focus when using a source of near-infrared light than using the visible light.
Loosen Tighten Focus lock knob
Pull and remove the cap
Day / Night GND IN
LL OFF
LOW
ELC ATW2 5SEC SOFT DC AUTO LOW DAY/NIGHT
WV-CP254H
Note: For the WV-CP254H Color CCTV Camera, do not use a transformer larger than 10VA.
POWER
SA 1965
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user�s authority to operate this equipment.
Black (Live)
r !6 y t u i o !0 !5
Camera mounting screw holes Fixing screws
Mount adapter
Power Cable
White (Neutral) Green/Yellow (Ground) BNC Plug BNC Plug
24 V AC, 60 Hz (19.5 V-28 V) (CLASS 2 SUPPLY ONLY)
SPECIFICATIONS
Pick-up device: Scanning area: Synchronization: Scanning system: Scanning: 752 (H) x 582 (V) pixels, interline transfer CCD 5.59 (H) x 4.68 (V) mm (equivalent to scanning area of 1/3 in. pick-up tube) internal, line-locked or multiplexed vertical drive (VD2), selectable 2 : 1 interlace 525 lines / 60 fields / 30 frames 15.734 kHz 59.94 Hz 480 lines 1.0 V [P-P] NTSC composite 75 � / BNC connector 50 dB (min) (at AGC Off, weight On) equivalent to continuous variable shutter speed between 1/50 s and 1/15 000 s 1.0 lx (0.1 foot-candle) at color mode, 0.15 lx (0.015 foot-candle) at black and white mode with F1.4 lens SHARP or SOFT, selectable CS-mount �10 °C - +50 °C (14 °F - 122 °F) less than 90 % 24 V AC 60Hz, 3.3 W 67 mm (W) x 65 mm (H) x 72.5 mm (D) 2-5/8" (W) x 2-9/16" (H) x 2-7/8" (D) 0.33 kg (0.7 lbs) selectable COLOR FIX (� external terminal active) or AUTO
!2 !4 !1 !3
Video Output Cable
The serial number of this product may be found on the top of the unit. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. You should note the serial number of this unit in the space providedof your purchase to aid identification manent record and retain this instruction as a perin the event of theft. Model No. Serial No. WV-CP254H
BLC SHARP VIDEO COLOR HI ON AGC FIX INT HI ALC ATW1 1MIN
WV-C C
P2 54H
To Video IN (CAMERA IN)
WV-C P
Horizontal: Vertical: Horizontal resolution: Video output: Signal-to-noise ratio: Electronic light control: Minimum illumination: Aperture: Lens mount: Ambient operating temperature: Ambient operating humidity: Power source and power consumption: Dimensions (without lens): Weights (without lens): Day/Night
LL OFF
LOW
SA 1966
ATW2 5SEC SOFT DC AUTO LOW DAY/NIGHT
ELC
2
54H
BNC Plug
WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
q Auto Iris Lens Connector Supplies power and control signals to an auto iris lens (not supplied). w Focus Lock Knob
i Detail/Aperture Level Selector (SHARP, SOFT) The detail/aperture level can be selected with this selector. Set it to the desired position while observing the picture on the monitor. SHARP: Normal position. SOFT: Select this position when a Quad System is connected to this camera. � Power supply connection Recommended wire gauge sizes for 24 V AC line.
Copper wire size (AWG) Length (m) of cable (Approx.) (ft) #24 #22 #20 #18 (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2) 20 65 30 100 45 160 75 260
PREFACE
Panasonic�s WV-CP254H digital signal processing color CCD camera introduces a new level of high picture quality and high resolution through the use of a 1/3-inch interline transfer CCD image sensor having 752 horizontal pixels (picture elements), and digital signal processing LSI�s. This model offers cutting-edge technology for advanced video surveillance.
This knob adjusts the back-focal distance or picture focus. e Lens (option)
Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover of the supplied connector as shown in the diagram. The pin assignment of the lens connector is as follows: Pin 1: Power source; +9 V DC, 50 mA max. Pin 2: Not used Pin 3: Video signal; 0.7 V[p-p]/40 k� Pin 4: Shield, ground
Pin 3 Pin 1 Pin 4 Pin 2 Rib
o Automatic Light Control/Electronic Light r Mount Adapter The camera mounting screw hole is for mounting the camera onto a mounting bracket. The camera is originally designed to be mounted from the bottom, however, a top-mounting type is also available. To mount from the top, Control Selector (ALC, ELC) Lets you select the mode according to the lens type used. ALC: Select this mode when an auto iris lens (ALC lens) is used with this camera. ELC: Select this mode when a fixed iris lens or manual iris lens is used with this camera.
FEATURES
1. The following functions are built in. (1) Auto Light Control (ALC)/Electronic Light Control (ELC) (2) Automatic Gain Control (AGC) and Automatic Tracing White Balance (ATW) (3) Camera synchronization mode selectable between internal (INT), Line-locked (LL) and Multiplexed Vertical Drive (VD2). 2. Minimum Illumination of 1.0 lx (0.1 foot-candle) at color mode, 0.15 lx (0.015 foot-candle) at black and white mode with F1.4 lens. 3. Signal-to-noise ratio of 50 dB (min) (at AGC OFF, weight ON) 4. Horizontal resolution of 480 lines 5. Auto iris lens control selectable between video signal and DC power supply. 6. Auto black-and-white mode enables the camera to switch between color and black and white picture in response to light input.
remove the mount adapter from the bottom of the camera by removing two fixing screws. Attach the mount adapter to the top as shown in the diagram, then mount the camera on the mounting bracket. Make sure that two original screws are used when mounting the mount adapter; longer type screws may damage inner components, too shorter type screws may cause the camera drop. t Synchronization Mode Selector (INT, LL) Selects the camera synchronization mode as either internal sync mode (INT) or line-lock mode (LL). INT: Sets to internal 2:1 interlace. LL: Sets to Line-lock mode. y Back Light Compensation Mode Selector (BLC ON, OFF) 3. Do not expose the camera to rain or moisture, or try to operate it in wet areas. Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock. Lets you select the mode according to the position of the object and light conditions on the screen. ON: Select this mode when a strong light such as a spotlight is in the background. OFF: Normal picture The factory default setting is ON. u AGC Level Selector AGC level can be selected with this selector. AGC automatically controls the gain of Image brightness level. HI: This setting raises more the gain and brightness of images under low light conditions. LOW: Normal position
Cautions: 1. Shrinking the cable-entry seal is a one-time procedure. Do not shrink the cable-entry seal until it has been ascertained that the unit is functioning. 2. CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY. Be sure to connect the grounding lead to the GND terminal. 3. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the Input Terminal. 4. The connections should comply National electrical Code (NEC). with
Weights and dimensions indicated are approximate. Specifications are subject to change without notice.
!0 Lens Drive Signal Selector (VIDEO, DC) Lets you select the mode according to the type of auto iris lens drive signal to be supplied to the lens from the auto iris lens connector. VIDEO: Select this mode if you are using a auto iris lens that requires a video drive signal. DC: Select this mode if you are using a auto iris lens that requires a DC drive signal. !1 Auto-Tracing White Balance mode (ATW) Selector The ATW mode can be selected with this selector. ATW1: Normal picture ATW2: ATW in sodium lamp mode !2 Day/Night Mode Selector This function switches the condition of pictures from color to black and white in low light conditions. COLOR FIX: Color picture reverts to blackand-white picture when an external day/night switching signal is received (refer to Day/Night connections). Note: When using this unit with infrared rays or lighting of which color temperature is 3 000 K or less, select this mode without fail, and short-circuit the Day/Night input terminals if you select the black-and-white picture. (The AUTO mode may cause hunting.)
STANDARD ACCESSORIES
Operating Instructions (this document) ............................................. 1 pc. The following parts are for installation: Body cap ........................................................................................... 1 pc. ALC lens connector (YFE4191J100) .................................................. 1 pc. C-mount Adapter ............................................................................... 1 pc.
Solder the lens cable to the pins of the supplied connector.
Mounting the Lens
Caution: Before you mount the lens, loosen the focus lock knob, and rotate it clockwise until it stops. If the ring is not at the end, the inner lens or CCD image sensor may be damaged. q Mount the lens by turning it clockwise on the lens mount of the camera. Note: When mounting the C-mount lens on the camera, mount the C-mount adapter by rotating it clockwise in advance. w Connect the lens cable to the auto iris lens connector on the side of the camera.
Lens mount C-mount adapter
WV-C C
Video Cable
1. It is recommended to use a monitor whose resolution is at least equal to that of the camera. 2. The maximum extensible coaxial cable length between the camera and the monitor is shown below.
Type of coaxial cable Recommended (m) maximum cable length (ft) RG-59/U RG-6/U RG-11/U RG-15/U (3C-2V) (5C-2V) (7C-2V) (10C-2V) 250 825 500 1 650 600 1 980 800 2 640
OPTIONAL ACCESSORIES
Lenses: WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3, WV-LA908C3, WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LZ61/15, WV-LZA61/2, WV-LZF61/2
PRECAUTIONS
1. Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service person for servicing. 2. Handle the camera with care. Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage.
4. Do not use strong or abrasive detergents when cleaning the camera body. Use a dry cloth to clean the camera when dirty. In case the dirt is hard to remove, use a mild detergent and wipe gently. Afterwards, wipe off the remained part of the detergent in it with a dry cloth.
P254H
Installation of Auto Iris Lens Connector
Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers.
w
Panasonic Digital Communications & Security Company Unit of Matsushita Electric Corporation of America Security Systems Group www.panasonic.com/cctv
Focus lock knob
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Zone Office Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
PANASONIC CANADA INC. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 PANASONIC SALES COMPANY DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC. San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00985 (809)750-4300
2003
© Matsushita Electric Industrial Co., Ltd. All rights reserved.
