PANASONIC WVCS854B
Instrukcja Obsługi

� PIX OFF Setting (PIX OFF) In this setting, you can assign a blemish position and compensate the blemish. 1. Move the cursor to PIX OFF and press the CAM (SET) key. The PIX OFF menu appears.

** PIX OFF ** 1* 5* 2* 6* 3* 7* 4* 8

** SPECIAL2 ** CHROMA GAIN � ����|����+ AP GAIN � ����|����+ PEDESTAL � �|�������+ HUE �����|����+ RESOLUTION NORMAL DNR LOW2 BW MODE PIX OFF REFRESH �PUSH SET CAMERA RESET �PUSH SET RET

000 000 RET

For WV-RM70, hold down the right and left buttons simultaneously for 2 seconds or more. For WV-CU360C/CJ and WV-CU161C, hold down the [4] and [6] keys simultaneously for 2 seconds or more. � Camera Resetting (CAMERA RESET) Move the cursor to CAMERA RESET with the joystick and press the F3 button of WV-CU550C/CJ.
** SPECIAL2 ** CHROMA GAIN � ����|����+ AP GAIN � ����|����+ PEDESTAL � �|�������+ HUE �����|����+ RESOLUTION NORMAL DNR LOW2 BW MODE PIX OFF REFRESH �PUSH SET CAMERA RESET �PUSH SET RET

2. Select a number and press the CAM (SET) key. The blemish compensation appears. position setting screen

Move the joystick to place the "+" cursor on the blemish position. After moving the "+" cursor to a position where the blemish looks inconspicuous, press the CAM (SET) key. Consequently, the blemish compensation position is set up and the PIX OFF menu is restored. After a blemish compensation position is set up, "*" is attached at the right of the number. 3. If you would like to delete a blemish compensation position, move the cursor to the applicable number and press the CAM (SET) key.

The camera is reset to the factory default settings. For WV-RM70, hold down the right, left and set switches simultaneously for 2 seconds or more. For WV-CU360C/CJ and WV-CU161C, hold down the [4], [5] and [6] keys simultaneously for 2 seconds or more. Note: In case of performing this operation on the condition that the cursor is positioned on other than CAMERA RESET, you cannot perform the operations on the menu thereafter. In that event, set the camera menu to ON again with the controller referring to page 12. � To Close the SPECIAL2 Menu Move the cursor to RET and press the CAM (SET) key. The setup menu appears on the monitor screen.
** SPECIAL2 ** CHROMA GAIN � ����|����+ AP GAIN � ����|����+ PEDESTAL � �|�������+ HUE �����|����+ RESOLUTION NORMAL DNR LOW2 BW MODE PIX OFF REFRESH �PUSH SET CAMERA RESET �PUSH SET RET

+

The blemish compensation position setting screen appears. Press the F2 button of WV-CU550C/CJ when the setting screen is active. For WV-RM70, hold down the right and left buttons simultaneously for 2 seconds or more. For WV-CU360C/CJ and WV-CU161C, hold down the [4] and [6] keys simultaneously for 2 seconds or more. The screen is restored to the PIX OFF menu, the blemish compensation position is deleted and "*" is also deleted from the right of the number.

� To Restore the Camera Default Position (REFRESH) Move the cursor to REFRESH with the joystick and press the F2 button of WV-CU550C/CJ.

Reset to the Factory Default Settings Any of the above settings plus the ALC/MANUAL level control and phase adjustments can be reset to the factory default settings by placing the cursor over the desired mode and then pressing the F2 button of WVCU550C/CJ. -42-