PANASONIC WVCW244S
Instrukcja Obsługi

� Heater unit installation
See OPTIONAL HEATER UNIT for details.
Adhesive tape Fold Supplied screw Harness

� Image Adjustment
You can manually adjust the pan/tilt/azimuth angles, focus, and zoom while observing the connected monitor.
Variable angles plus or minus 75 ° (max.)

SPECIFICATIONS
Pick-up device: Scanning area: Scanning: Horizontal: Vertical: Synchronization: Video output: Horizontal resolution: Signal-to-noise ratio: Minimum illumination: 768 (H) x 494 (V) pixels, Interline transfer CCD 4.8 (H) x 3.6 (V) mm (Equivalent to 1/3� pick-up tube) 525 lines/60 fields/30 frames 15.734 kHz 59.94 Hz Internal, Line-lock (only 24 V AC), or Multiplexed vertical drive (VD2) 1.0 V [P-P] NTSC composite 75 �/BNC connector 480 lines 50 dB (Equivalent to AGC Off, weight On) 2.4 lx (0.24 footcandle) (WIDE), When the optional WV-CW2C dome cover is installed. 1.0 lx (0.1 footcandle) (WIDE), SHARP or SOFT, selectable ATW CS-mount 3.8 mm - 8 mm 1:1.4 (Wide), 1:1.8 (Tele) Horizontal: 35.6 � - 73.6 � Vertical: 26.6 � - 53.4 � 1.2 m - � (3.9 ft - �) �10 °C - +50 °C (14 °F - 122 °F) �30 °C - +50 °C (�22 °F - 122 °F) (When the optional heater unit built in) Less than 90 %

OPTIONAL HEATER UNIT
� Optional Heater Unit WV-CW3H
� Introduction
Installing this heater unit enables the camera to operate under in a low-temperature environment of �30°C (�22°F). The heater turns on automatically when the temperature inside the camera drops below +10°C (50°F) and turns off when it rises. A small fan inside the unit will minimize condensation on the surface of the dome cover caused by changes in ambient temperature unless temperatures change too rapidly. The fan will stop when there is no possibility of condensation.

Point �A� (inside the wall)

� Precautions
� This product should be installed and connected by qualified service personnel or system installers. � Do not use the same 24 V AC power source supplying the power to the camera for the heater unit. Connect another 24 V AC power source to the heater unit. If the same power source is used, turning the heater on and off may disturb the camera images. � When servicing, pay attention to high temperature on the surface of the unit. Disconnect the harness and wait until it cools. � When you install the camera in a low-temperature location and start operating it, it may take time (around 30 minutes) for the inside of the camera to warm up. Cut power once then Supplied screw Supplied screw supply power again.
Adhesive tape Adhesive tape Fold Fold Harness Harness

Pan lock screw (stainless)

Notes: � Do not hold the camera by lens unit to adjust panning, tilting, or azimuth. � The video output to the BNC will be interrupted while an LCD monitor is connected to the video jack.

Panning table

Tilting lock screw (stainless)

Detail: White balance: Lens Mount: Lens Focal length: Maximum aperture ratio: Angular field of view: Focusing range: Ambient operating temperature: Ambient operating humidity: Power source and Power consumption:

� Mounting the camera
1. Fix the camera to the installation surface. WV-CW244F � Fix the camera on the junction box using four screws (locally procured). WV-CW244S � Fix the supplied bracket on the wall/ceiling using four screws (locally procured). � Fix the camera on the bracket using four screws (supplied). 2. Perform connections referring to � Connections. 3. Reinstall the camera to the bracket or junction box referring to step 1 above. 4. Adjust the image referring to � Image Adjustment. 5. Apply waterproof means referring to � Waterproof Process.

1. Connect an LCD monitor to the video jack. 2. Pan/tilt/azimuth adjustment � Loosen the two screws locking the pan and tilt tables. � Pan and tilt the table to aim the camera at what you need to watch. � Turn the azimuth adjuster to obtain a level image. � Tighten the two screws after adjusting.

� Installation
12 V DC, 265 mA (Camera) 24 V AC 60 Hz, 3.0 W (Camera) 24 V AC 60 Hz, 12.1 W (Heater unit) WV-CW244F: 133 mm (H) x 152.5 mm (D) WV-CW244S: 5-1/4� (H) x 6� (D) 136.5 mm (H) x 160 mm (D) 5-3/8� (H) x 6-5/16� (D) 1.2 kg (2.7 lbs.) 1.7 kg (3.8 lbs.) 1. Open the dome cover. (See Disassembling the camera.) 2. Place the heater unit in the camera and fix it with the supplied screw. 3. Insert the harness into the heater unit connector of the camera. 4. Fold the desiccant pack in half, and attach it with adhesive tape to point "A" shown in the figure. Note: Attach the desiccant pack so that it

Dimensions:

Azimuth adjuster

Weights:

WV-CW244F: WV-CW244S:

3. Zoom � Unlock the zoom lever. � Move the lever to adjust the zoom. � Lock the lever.

Point �A� Point �A� (inside the wall) (inside the wall)

Weights and dimensions indicated are approximate. Specifications are subject to change without notice.

does not block ventilation holes or hang over the top of the wall. 5. Attach the dome cover while paying attention not to pinch the harness cable. 6. Connect the heater power cable of the camera. (See Connection.)

STANDARD ACCESSORIES
FAR TELE

NEAR WIDE

Operating Instructions (this document) ............................................. 1 pc. The following are for installation. Tamperproof screw bit ...................................................................... 1 pc. Camera mounting bracket (supplied only to WV-CW244S) ............... 1 pc. Camera fixing screw (with a plastic washer) ..................................... 4 pcs. (supplied only to WV-CW244S)

� Specifications
Required power: Power consumption: Dimensions: Weights: 24 V AC, 60 Hz 12.1 W maximum 29 mm (H) x 83 mm (W) x 89.5 mm (D) [1-1/8� (H) x 3-1/4�(W) x 3-1/2�(D)] 45 g (0.1 lbs)

� Connections
� Video Output Connection
Connect the video output connector to the monitor or other system device with the procured coaxial cable. The maximum extensible length is shown in the table.
Type of coaxial cable Recommended (m) maximum cable length (ft) RG-59/U RG-6/U RG-11/U RG-15/U (3C-2V) (5C-2V) (7C-2V) (10C-2V) 250 825 500 1 650 600 1 980 800 2 640
�

Cable Length and Wire Gauge

Zoom lock lever Focus lock lever

24 V AC The recommended cable length and thickness are shown in the table for reference. The voltage supplied to the power terminals of the camera should be within 19.5 V AC and 28 V AC. Recommended wire gauge for 24 V AC line.
Copper wire size (AWG) Length of (m) Cable (Approx.) (ft) #24 (0.22 mm2) 95 314 #22 (0.33 mm2) 150 495 #20 (0.52 mm2) 255 842 #18 (0.83 mm2) 425 1 403

OPTIONAL ACCESSORIES
Heater unit ......................................................................................... WV-CW3H Clear dome cover .............................................................................. WV-CW2C Camera mounting bracket (for WV-CW244F) .................................... WV-Q112

� Accessories
Fixing screw (M3 x 12) ...................................1 pc. Desiccant pack .............................................1.pc.

4. Focus � Unlock the focus lever. � Move the lever to adjust the focus. � Lock the lever. 5. Reinstalling the dome cover � Attach the dome cover to the camera. � Tighten the three tamper-proof screws.

� Power Connection
�

Wire Colors & Functions

Camera power cable

12 V DC Use the formula below to calculate the power cable and power supply. The voltage supplied to the power terminals of the camera should be within 10.5 V DC and 16 V DC. Resistance of copper wire [at 20 °C (68 °F)]
Copper wire size (AWG) Resistance �/m #24 (0.22 mm2) 0.078 0.026 #22 (0.33 mm2) 0.050 0.017 #20 (0.52 mm2) 0.03 0.010 #18 (0.83 mm2) 0.018 0.006

� Waterproof Process
When necessary, apply waterproof process to protect the camera from water soak. 1. Power cord First, tape the individual wires, finally all of them as a whole.

Power cord

Wire Color Black White Green/Yellow

24 V AC 24 V AC (L) 24 V AC (N) Ground

12 V DC Positive Negative Not Used

Resistance �/ft

2. Connector junctions Tape the BNC-BNC junction point.
10.5 V DC � VA � 2(R x I x L) � 16 V DC L : Cable length (m) (ft) R : Resistance of copper wire (�/m) (�/ft) VA : DC output voltage of power supply unit

Heater power cable

I : DC current consumption (A). See specifications.

Video output cable

3. Gaps and holes Apply such a waterproof material as silicone clay (rubber) to the gaps, screws, holes, and other relevant portions. 4. Camera Fixing Screws WV-CW244F Be sure to apply silicone rubber to the camera fixing screws in case of outdoor installation. WV-CW244S If you use camera fixing screws that are locally procured, be sure to apply silicone rubber to the screws.

Wire Color Red White

24 V AC 24 V AC (L) 24 V AC (N)

Panasonic Digital Communications & Security Company Unit of Matsushita Electric Corporation of America Security Systems Group www.panasonic.com/cctv
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Zone Office Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840

PANASONIC CANADA INC. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 PANASONIC SALES COMPANY DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC. San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00985 (809)750-4300

Caution: � Be sure to connect the GND (grounding) lead of the camera and grounding terminal of the power supply when using a 24 V AC power source.

2003

© Matsushita Electric Industrial Co., Ltd. All rights reserved.