|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
SETTING CLOCK RESETTING THE MICROCOMPUTER
Reset microcomputer under the following conditions: q To erase all of the stored memory contents (clock and timer
settings, tuner and CD presets). (0:00) system. q If the display is not correct.
1 2
ON/
(0:00 23:59)
Press ON/STAND-BY button to enter the stand-by mode. In this example, clock is set for the 24-hour
1
Press the MEMORY/SET button. q If the operation is not correct.
3 3 1 Press PRESET ( or ) button to select the time display Press ON/STAND-BY button to enter the stand-by mode. 3
Whilst pressing down MEMORY/SET button and the X-
3 2
(AM 12:00 PM 11:59) AC INPUT socket on this unit.
mode. Unplug power lead from the AC INPUT socket on this "0:00" � The 24-hour display will appear. unit. STAND-BY
"AM 12:00" � The 12-hour display will appear. BASS/EQUALIZER button, plug AC power lead into the
q Note that this can only be set when the unit is first installed Caution:
memory, such as clock timer settings, tuner and CD pres-
2,3
or it has been reset (see page 6). q The operation explained above will erase all data stored in
MEMORY/ Press the MEMORY/SET button. PRESET ets.
4
SET ( / ) 5
Press PRESET ( or ) button to adjust the hour.
q Press PRESET button once to advance the time by 1 hour. ON/
STAND-BY PRESET
Hold it down to advance continuously.
q When the 12-hour display is selected, "AM" will change auto-
( / ) matically to "PM".
SET 6 Press the MEMORY/SET button.
PREPARATION FOR USE MEMORY/
Press PRESET ( or ) button to adjust the minutes.
s Remote control 7
becomes erratic.
q Press PRESET button once to advance the time by 1 Notes concerning use:
minute. Hold it down to change time in 5 minute intervals. q Replace the batteries if control distance decreases or operation
q The hour setting will not even if minutes advance from
"59" to "00". q Periodically clean transmitter LED on the remote control
(8" Press the MEMORY/SET button. 20') q Exposing sensor on the main unit to strong light may in-
2 8
1 5 q Keep the remote control away from moisture, excessive heat, 1
and sensor on the main unit with a soft cloth. 0.2 6 m
q The clock starts operating from "0" seconds. (Seconds are not terfere with operation. Change lighting or the direction of
OPERATION MANUAL
�5�
displayed.) the unit.
3
shock, and vibrations.
Note: q In event of a failure or when the AC power lead is disconnected, the clock display will go out. 0:00 AM 12:00 When AC power supply is restored, the clock display will flash on and off to indicate time when the power failure occurred or when the AC power lead was disconnected. If this happens, follow procedure below to change the clock time.
4
To change the clock time: 5
1 Press ON/STAND-BY button to enter the stand-by mode. 2 6 Perform steps 4 8 above.
7
To change the time display mode:
1 Perform steps 1 3 in the section "RESETTING THE MICRO-
COMPUTER", on page 6.
XL-520W/CP-520
8 2 Perform steps 1 8 above.
|
|
|
> |
|
