|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
XM-405EQX
SERVICE MANUAL
US Model Canadian Model AEP Model UK Model E Model
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US, Canadian model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 40 watts/100 watts per channel minimum continuous average power into 4 ohms, 5 channels driven from 20 Hz to 20 kHz/200 Hz with no more than 0.04% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications
Circuit system OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Speaker impedance 2 � 8 � (stereo) 4 � 8 � (when used as a bridging amplifier) Maximum outputs 80 watts � 4 + 200 watts � 1 (at 4 �) Rated outputs (supply voltage at 14.4 V) 5 Speakers: 40 watts � 4 (20 Hz � 20 kHz, 0.04% THD, at 4 �) + 100 watts � 1 (20 � 200 Hz, 0.04% THD, at 4 �) 50 watts � 4 (20 Hz � 20 kHz, 0.1% THD, at 2 �) + 125 watts � 1 (20 � 200 Hz, 0.1% THD, at 2 �) 3 Speakers: 100 watts � 2 (20 Hz � 20 kHz, 0.1% THD, at 4 �) + 100 watts � 1 (20 � 200 Hz, 0.04% THD, at 4 �) Frequency response 5 Hz � 100 kHz ( +0 dB) �3 Harmonic distortion 0.005% or less (at 1 kHz, 4 �) Input level adjustment range 0.2 � 4.0 V (RCA pin jacks) 0.4 � 8.0 V (High level input) High-pass filter 50 � 200 Hz, �12 dB/oct Low-pass filter 50 � 200 Hz, �12 dB/oct Low boost 0 � 10 dB (40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.5 � 16 V Current drain at rated output: 33 A Remote input: 1.5 mA Dimensions Approx. 260 � 55 � 450 mm (w/h/d) (10 1/4 � 2 1/4 � 17 3/4 in.) not incl. projecting parts and controls Mass Approx. 4.7 kg (10 lb. 6 oz.) not incl. accessories Supplied accessories Mounting screws (4), Terminal cap (1) Design and specifications are subject to change without notice.
Notes on Chip Component Replacement � Never reuse a disconnected chip component. � Notice that the minus side of a tantalum capacitor may be damaged by heat.
STEREO POWER AMPLIFIER
MICROFILM
�1�
|
|
|
> |
|
