jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
Pin Name FLASH-W IIC SIO IIC CKO RC-IN1 X1A X0A DAVN KEYACK BU-IN ILL IN TEL-ATT NOSESW ACC IN
TIR-D0 to TIR-D3
I/O I I/O O I O I I I I I I I I I/O I I I I I � I O � I O O O O O O I I I I I I I
Function Internal flash memory data write mode detection signal input terminal �L�: data write mode Not used (fixed at �H� in this set) Two-way data bus with the RDS decoder (IC150) Bus clock signal output to the RDS decoder (IC150) Rotary remote commander shift key input terminal �L�: shift Sub system clock output terminal (32.768 kHz) Sub system clock input terminal (32.768 kHz) Data transmit completed detect signal input from the RDS decoder (IC150) �H� active Input of acknowledge signal for the key entry Acknowledge signal is input to accept function and eject keys in the power off status On at input of �H� Battery detect signal input from the SONY bus interface (IC602) and battery detect circuit �L� is input at low voltage Auto dimmer control illumination line detection signal input terminal �L� is input at dimmer detection Telephone muting signal input terminal At input of �H�, the signal is attenuated by �20 dB Front panel block remove/attach detection switch (SW500) input terminal �L�: front panel is attached Accessory detect signal input terminal �L�: accessory on Two-way data bus with the MSM6688GS (IC100) Hardware standby input terminal �L�: hardware standby mode Reset signal input in this set Setting terminal for the CPU operational mode (fixed at �L� in this set) Setting terminal for the CPU operational mode (fixed at �H� in this set) Setting terminal for the CPU operational mode (fixed at �H� in this set) System reset signal input from the reset signal generator (IC500) and reset switch (SW800) �L�: reset �L� is input for several 100 msec after power on, then it changes to �H� Ground terminal Main system clock input terminal (3.68 MHz) Main system clock output terminal (3.68 MHz) Power supply terminal (+5V) Busy detection signal input from the MSM6688GS (IC100) �H� is output while MSM6688GS (IC100) is executing a command Data write strobe signal output to the MSM6688GS (IC100) �L� is output when data (D0 to D3) are output to the MSM6688GS (IC100) Chip enable signal output to the MSM6688GS (IC100) TIR-WR (pin (§) or TIR-RD (pin `���) is accepted when CE is �L� or CE is �H� respectively TIR-WR (pin (§) or TIR-RD (pin `���) is not accepted when CE is �H� or CE is �L� respectively Reset signal output to the MSM6688GS (IC100) �H�: reset Power down control signal output to the MSM6688GS (IC100) �L�: power down Data read strobe signal output to the MSM6688GS (IC100) �L� is output when data (D0 to D3) are output to the MSM6688GS (IC100) Metal detection signal input terminal �L�: normal position, �H�: metal position Whether a music is present or not from CXA2510AQ (IC250) is detected at auto music sensor �L�: music is present, �H�: music is not present Rotation detect signal input from supply reel sensor and take-up reel sensor on the deck mechanism Tape position (EJECT/FF/REW/ REV/FWD mode) detect input from the tape operation switch on the deck mechanism POS0: �L�: EJECT mode, �H�: others mode POS1: �L�: FF and FWD mode, �H�: others mode POS2: �L�: REW mode, �H�: others mode POS3: �L�: REV and EJECT mode, �H�: others mode
