Gruba instrukcja - poprostu wszystko co potrzreba - polecam .
Tekstowy podgląd strony 7 (kliknij aby zobaczyć)
INSTALLATION
Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown.
HINTS AND TIPS
Important
Normal Operating Sounds
It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation. Depending upon the position which you choose for your appliance, you may wish to reverse the way in which the door opens. To do this, refer to instructions on �Door reversal�. � You may hear faint gurgling or bubbling sounds when the refrigerant is pumped through the coils or tubing at the rear, to the cooling plate/evaporator. When the compressor is on, the refrigerant is being pumped round, and you will hear a whirring sound or pulsating noise from the compressor. A thermostat controls the compressor, and you will hear a faint �click� when the thermostat cuts in and out.
Energy Saving Advice
� � Do not install the appliance close to sources of heat, such as a boiler or radiator. Locate the appliance in a cool well ventilated room and make sure that the air openings of the appliance are not obstructed. Avoid unnecessary frosting in the cabinet by packing all foodstuffs into airtight packages before placing them in the freezer. Always leave warm food to cool down to room temperature before placing in the fridge. Food which is to be frozen (when cool) should be placed in the fridge before being transferred to the freezer. Thaw frozen food in the fridge. This will ensure safer defrosting of foods and reduce the work of the refrigeration unit. Try to avoid keeping the door open for long periods or opening the door too frequently as warm air will enter the cabinet and cause the compressor to switch on unnecessarily often. � Ensure there are no obstructions preventing the door from closing properly.
Important
IF YOU ARE DISCARDING AN OLD APPLIANCE THAT HAS A LOCK OR CATCH ON THE DOOR, YOU MUST ENSURE THAT IT IS MADE UNUSABLE TO PREVENT YOUNG CHILDREN BEING TRAPPED INSIDE.
�
�
�
Positioning
This appliance should only be installed at a location where the ambient temperature corresponds to the climate classification indicated on the rating plate, which is located at the left on the inside of the appliance. The following table shows which ambient temperature is correct for each climate classification: SN N ST T +10°C to + 32°C +16°C to + 32°C +18°C to + 38°C +18°C to + 43°C A B
10 mm 10 100 mm
Food Storage
To obtain the best performance from your fridgefreezer � � Do not store warm food or evaporating liquids. Avoid buying frozen food if you cannot store it straight away. The use of an insulated container is advisable. When you arrive home place the frozen food in the freezer immediately. Keep the time between buying chilled food and placing it in your refrigerator as short as possible. Do not push food together too much, try to allow air to circulate around each item. Do not store food uncovered. Ensure that food placed in the freezer is dated and labelled and used in date order to ensure that food is consumed at its best. Remove suspect food from your refrigerator and clean, refer to Maintenance and Cleaning. Lean food keeps better and longer than fatty food, salt reduces the storage time. Wrap the food in polythene or aluminium freezing bags or foil so that they adhere to the food and provide an airtight seal . Packaging which is swollen or has traces of refrozen water droplets on the pack could indicate that the product has not been kept at a suitable temperature and that it may have lost its original quality. Partially thawed food must not be refrozen, it must be consumed within 24 hours. Never exceed the storage times indicated by the manufacturer. The symbols on the drawers show different types of frozen goods. The numbers indicate storage times in months for the appropriate types of frozen goods. Whether the upper or lower value of the indicated storage time is valid depends on the quality of the foods and pre-treating before freezing.
� �
�
�
� � �
NP002
It should be located in a dry atmosphere, out of direct sunlight and away from extreme temperature e.g. not next to a boiler or radiator, or in a very cold room e.g. an outhouse, where the temperatures may fall below 10°C (50°F). If these temperatures are exceeded i.e. colder or warmer, then the appliance may not operate correctly. You should also ensure that air can circulate freely around the back and the top of the cabinet. There must also be at least 100 mm (4�) distance between the top of the cabinet and any overhanging kitchen furniture (A). Ideally, the appliance should not be positioned beneath overhanging furniture (B). There should also be a gap of 25 mm either side of the appliance. Do not obstruct the space underneath. The back of the cabinet may be placed close to the wall but must not touch it. DO NOT install in places with restricted ventilation. Adjust the level of the appliance by screwing out the adjustable foot, or feet, at the bottom of the cabinet using your fingers or a tool (see figure).
In the Event of a Power Failure
If there is a power failure during the storage of frozen foods, keep the door closed. If the temperature within your freezer should rise, do not refreeze the food without checking its condition. The following guidelines should assist you: Ice-cream: Once thawed should be discarded. Fruits & Vegetables: If soft should be cooked and used up. Breads & Cakes: Can be refrozen without danger. Shellfish: Should be refrigerated and used up quickly. Cooked Dishes: i. e. casseroles should be refrigerated and used up. Large Pieces of Meat: Can be refrozen providing there are still ice crystals remaining within them. Small Joints: Should be cooked and can then be refrozen as cooked dishes. Chicken: Should also be cooked and refrozen as a fresh dish.
�
� � �
�
D200
Rear spacers
� The plastic bag containing all relevant documentation also contains two spacers to be fitted into special holes in the back of the appliance. Fit the spacers into the holes, taking care to ensure that the arrow (A) is positioned as shown in the diagram. Then turn them through 45° (arrow (A) vertical) until they lock into place. 14
A
45°
PR60
