VERSION WiTH BATTERY IGNITION Change of battery - Unscrew the screw " A ". - Open the door " B ". - Unscrew cover " C ". - Insert battery " D ". (1x AA size battery, whit positive terminal turned in the direction of the cover " C "). - Remount everything by following the inverted operations.
B) The hob is fixed in its upper part to the burners by means of some visible screws. If these screws and the nut blocking the taps to the hob are screwed, it is possible to open the appliance and to reach the inside components (see picture below).
GENERAL INFORMATION DESTINED TO THE END USER FIRST PART
WORK-TOP USE USING GAS BURNERS The following symbols are on the control panel next to each knob: - Black circle gas off maximum setting minimum setting
ENVIRONMENT PROTECTION Packing disposal Sort packing into different materials (cardboard, polystyrene etc.) and dispose of them in accordance with local waste disposal laws. This appliance must only be used for the purpose of domestic cooking.
- Large flame - Small flame
The minimum position is at the end of the anti-clockwise rotation of the knob. All operation positions must be chosen between the positions of max. and min., never choose them between max. and off.
B D A C
APPLIANCE MAINTENANCE WARNINGS Before performing any repair or operation, switch the appliance off and close the gas tap. The manufacturer declines all responsibility for any damage to persons, animals or things caused by failure to observe the rules indicated above. In case it is necessary to repair or replace the inside components, act as follows: DISASSEMBLE OF WORK-TOP - disconnect the electrical supply cable - disconnect the gas supply tube - remove the grids - remove burners and flame-spreaders - remove the knobs from the facia-panel - disassemble the work-top from the cabinet unscrewing screws Z blocking locking bridles Y (see paragraph �Assemblage and installation of the appliance�. Remove the hob from the top.
GREASING OF TAPS If a tap becomes hard to be turned, grease it using a specific grease withstanding high temperatures. Act as follows: - Switch the appliance off and close the gas tap. - Remove knobs, grids, burners and flame-spreaders. - Follow the indications od point A and B. - Unscrew the two fixing screws V from the burner body A (see picture) and remove the cone C.
THIS APPLIANCE HAS BEEN CONSTRUCTED AND DISTRIBUTED IN COMPLIANCE WITH: The safety requirements of Directive 73/23/EEC regarding �Low Voltages�. The requirements of Directive 89/336/EEC regarding �Electromagnetic Compatibility�. The safety requirements of Directive 90/396/EEC regarding �Gas Appliances�. Directive 89/109/EEC regarding �Materials that can touch food� Moreover the above mentioned Directives comply with Directive 93/68/EEC.
MANUAL IGNITION To turn on a burner, approach a match to it, press the knob corresponding to the selected burner and turn it anticlock-wise to the maximum position.
ELECTRIC IGNITION (Optional) To turn on a burner, press the knob corresponding to the selected burner and turn it anticlockwise to the maximum position; simultaneously pressing the electric ignition button on the control panel marked with . In case there is no electric current, the burner can also be lighted using a match.
V
V
-
AUTOMATIC ELECTRIC IGNITION (Optional) To turn on a burner, press the knob corresponding to the selected burner and turn it anticlockwise to the maximum position. Keeping the knob pressed, the electric automatic ignition of the burner will be started up. In case there is no electric current, the burner can also be lighted using a match.
C
This cooker is of type �X� with regard to protection against over heating of surraounding surfaces.
A
- Clean the cone C and its slot by means of a cloth soaked with diluent. - Slightly grease the cone with the relevant grease, put it in its slot, and turn it some times. - Remove the cone again, remove the exceeding grease making sure the gas entries are not obstructed by grease residuals. - Assemble everything carefully in the opposite direction. TAPS REPLACEMENT Act as follows: - Switch the appliance off, and close the general gas tap. - Remove knobs, grids, burners and flame-spreaders. - Disassemble the upper hob as previously described. - Follow the indications written in paragraphs A and B. - Unscrew nut L of the gas tube to the burner and disassemble the gas manifold from the hob lower plate. - Unscrew screws R fixing the tap to the bridle and remove the last (see picture). Note: Every time the tap is replaced, it is necessary to replace seal gasket D too (see picture). Once you have finished this procedure, re-assemble everything in the opposite sense, having care to check with water and soap the gas circuit seal.
A D
DEAR CUSTOMER, . Carefully read these instructions before using the appliance and keep them for future consultation. . Keep potentially hazardous packaging (plastic bags, polystyrene etc.) out of the reach of children.
APPLIANCES WITH SAFETY VALVE Follow case, however, once describedturned the knobthethe open In this the same procedure you have above to ignite to burners. setting, hold it pressed in for 10 seconds. If for any reason the burner flame goes out, the safety valve automatically shuts off the gas supply to the burner in question.
Y
NO
Z
NO
A) On the lower plate of the hob, on the outside there are some visible screws fixing the burners and the gas manifolds to the chassis or some screw-nuts fixing the electrical plates for all electric or combined versions. Once these screws or screw-nuts are unscrewed, it is possible to replace the components inside the hob (see picture below).
WARRANTY Your new appliance is covered by a warranty. The warranty certificate is herewith enclosed. If it is missing, ask the retailer for it indicating purchasing date, model, and data plate number which are printed on the data nameplate identifing the appliance. Keep the smallest part of the certificate, and in case of necessity, show it to the Technical Service together with the receipt or the delivery bill. If you do not follow this procedure, the technical service will be compelled to charge you with all the fees of each eventual reparation.
Max
Min
AFTER SALES SERVICE The excellent quality and advanced technology of our appliances guarantee their perfect operation. If, however, a fault occurs, try and remedy it by checking if you have correctly followed all the instructions indicated in this instructions booklet. If, after consulting these instructions and checking the gas and electrical connections, the fault persists, contact our After Sales Service for prompt technical assistance.
ENERGY SAVING TIPS . The diameter of the pan bottom should be the same as that of the burner. The burner flame must never come out from the pans diameter. . . . Use flat-bottomed pans only. Whenever possible, keep a lid on the pan while cooking. You will not need as much heat. Cook vegetables, potatoes, etc. with as little water as possible to reduce cooking times.
L
17
The diameter of the recommended pans is:
R
RAPID SEMIRAPID AUXILIARY
from 20 to 24 cm from 18 to 20 cm from 12 to 18 cm
