WHIRLPOOL AWM 8083/1
Instrukcja Obsługi

3gb05195a.fm5 Page 2 Friday, November 23, 2001 12:43 PM

CONSUMPTION DATA Temperature Selector Programme (°C) White Cotton Coloured cotton Coloured cotton Synthetics Synthetics Rapid Plus Delicates Wool Handwash 95 60 40 60 40 30 30 40 30 (kg) 6.0 6.0 5.0 2.5 2.5 3.0 1.5 1.0 1.0 (l) 54** 49 44 55 55 37 60 60 45 (kWh) 1.90 1.14 0.60 0.80 0.60 0.40 0.50 0.45 0.30 Load Water Energy Approx. Programme Duration (hours : minutes)* 2:00 2:20 2:05 1:30 1:20 0:30 0:45 0:40 0:40

�Rinse Hold� button � The laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from changing. � This option is particularly recommended for the programme �Synthetics� or �Delicates�. � This function is particularly useful if you want to postpone spinning to a later time, or if you want to drain only. Note: The programme stops to �Rinse Hold� at the time the �Rinse Hold� light in the programme flow indication is on. Terminate the �Rinse Hold� option: � Press the �Rinse Hold� button again; the programme will terminate automatically with the final spin cycle for the present wash programme. � If you do not wish to spin the clothes, turn the programme selector knob to the �Drain� programme and press the �Start/Pause� button again when flashing. �Spin Speed Reduction� button � Every programme has an automatic predefined maximum spin speed. � Press the button to set another spin speed. � If the spin speed �0� is selected, the final spinning is cancelled but intermediate spin peaks remain during rinse. The water is drained out only. START DELAY The �Start Delay� allows to run the machine at the consumer�s convenience, for example at night when electricity is cheaper. � Select programme, temperature and options. � Press the �Start Delay� button to select the delay time by 1 to 23 hours; � Press the �Start/Pause� button. � The time delay indication disappears when the programme starts and it is replaced by the remaining time. � The number of hours preselected can later be reduced pressing again the �Start Delay� button. To cancel the �Start Delay�. � Turn the programme selector to the � � position. � Reselect the desired programme and options and press the �Start/Pause� button.

PROGRAMME START Open the tap and press the �Start/Pause� button. The pilot lamp of the �Start/Pause� button lights up. The indicator lamps show the sequence reached in the programme. After starting the programme, the sequence indication runs from left to right through Wash, Rinse, Spin. When the sequence of the programme is finished the corresponding lamp goes out. DOOR LOCK The door can be opened when the �Door Open� indication is on. PROGRAMME END � The remaining time is on �0:00� and all the lights of the programme sequence indication are off. 1. Turn the programme selector to the � position. 2. Turn the water supply tap off. 3. Open the door and unload the machine. 4. Close the tap and leave the door ajar to allow the drum to dry out. CHANGE THE PROGRAMME, TEMPERATURE, OPTIONS AFTER PROGRAMME START 1. Press the �Start/Pause� button to pause the programme. The light flashes. 2. Select the new programme (with temperature), any options and another spin speed if you want. 3. Press the �Start/Pause� button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme. CANCEL A PROGRAMME BEFORE THE END 1. Press the �Start/Pause� button to pause the programme. The light flashes. 2. Set the programme selector to �Drain�. The spin indicators show �0� and the remaining time shows �0:02�. 3. Press the �Start/Pause� button to start the drain programme.
Whirlpool is a registered trademark of Whirlpool USA.

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. * The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household conditions applicable at that time. **To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

�

ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME Add the detergents as described in the programme table or in the chapter �Detergents and Additives� in the booklet. 1. Turn the programme selector knob to the desired programme. 2. The remaining time display shows the duration of the chosen programme (in hours and minutes) and the pilot lamp of the �Start/Pause� button is flashing. 3. The programme sequence and the predefined spin speed indication corresponding to the selected programme lights up. The recommended temperature (see the indicator) can be altered by pressing �+� or �-� button. SELECT ANY DESIRED OPTION Selecting any option the indication lights up. When the combination of programme, additional options and temperature is not possible, the indication lights switch off automatically. Unsuitable combinations of options are deselected automatically.

�Easy Ironing� button � Can be used together with Cotton and Synthetics programmes to make ironing easier. � Increases the water quantity and the clothes are spun very soft. �Eco� button � The duration of the wash is extended and the temperature reduced to save up to 40% of energy but maintaining good washing results. �Prewash� button � Only for heavily soiled loads (for example sand, granular dirt) sensible. The cycle time increases approximately 15 min. �Intensive Rinse� button � More water and a longer time in rinse cycle is added. � This option is particularly suitable for areas with very soft water, washing baby linen and helps people with allergies.

5019 301 05195/A
Black Process Plate