|
|
|
Kto jest w sklepie?
Sklep przegląda 6043 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Schematy są ale można wysilić się i zrobić kolorowy skan i o większej rozdzielczości. Wtedy schematy płytek będą czytelniejsze. Całość super jako wartość merytoryczna. Wszystkie dane potrzebne do podłączenia różnego rodzajów urządzeń takich gramofon, CD itd.
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
3. Data Transfer program
When the main board of a customer's cellular phone is required to be replaced with a new one, or the customer is needed to use a phone lent from the service center while his phone is serviced, this feature is used to transfer(copy) all the EEPROM data of the customer's phone into the new board or the lent phone to keep the information the customer had stored into his phone personally. 3. Press <F1> key to read EEPROM data from the customer's cellular phone. On screen, 'Change the mode of the phone from HANDS-FREE mode to DM mode' message appears. On the LCD display of the phone, 'AUTO TEST' and 'WRITE EEPROM' messages appear. If the phone is already in DM(Diagnostic Monitor) mode, the message does not appear. 4. After the mode is changed to DM, EEPROM data on the cellular phone is read by PC. You can monitor the reading procedure on the screen. 5. When the data reading is completed, 'Replace the source phone with the target phone and press <F5> when ready' message appears on the screen. 6. Press any key to clear the message. The cellular phone displays 'DELETED' and '300-300-3000' instead of greeting and phone number respectively. All the features of the phone including ESN are reset to default status, and the phone can not be operated. 7. Remove the phone from the test jig and connect the new phone to the test jig. Caution: If you try to perform reading again without writing after reading is already done once, the error message 'READING FROM THE PHONE WAS ALREADY BEEN CARRIED OUT, WRITING SHOULD BE CARRIED OUT' appears on the screen. 8. Press <F5> key to perform writing EEPROM data. You can monitor the writing procedure on the screen. 9. When the data writing is completed, the phone will reset. The program returns to standby mode and is ready to read data from another phone. 'WELL DONE, DATA TRANSFER IS COMPLETED' appears on the screen. 10. Check if the transferred EEPROM data is the same.
3-1 Getting Started
1. Run the DTRANxx.EXE file. If you run the file for the first time, the message 'INITIAL FILE IS CREATED' appears. Do not delete the created file because the file creates DTRANxx.CFG to store environment setup data. The message does not appear once you have run the program. 2. Press any key to go to next procedure. Function Keys Fl Reads EEPROM data from the customer's cellular phone. F5 Writes the data of the customer's phone into the EEPROM on the new board.
ALT+X Exits programming and returns to DOS mode.
3-2 Operation Procedure
1. On standby mode, 'Please check the communication link between your PC and the phone prior to beginning ...' messages appear on the screen. You are ready to transfer data. 2. Switch the phone power on after you have run the program.
Samsung Electronics
3-1
|
|
|
> |
|
