|
|
|
Kto jest w sklepie?
Sklep przegląda 6011 gości i
32 zarejestrowanych klientów |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
SCD-XB770
Ver 1.1 2001.07
4-5 . AGING MODE (� Perform as necessary) The aging can be performed to the set in the test mode. The aging can be continued by the set number of times or until an error occurs. In the aging, the following operations are repeated. Table turntDisc chuckingtDisc detecttServo ontAuto adjustmenttTOC readingtPlay of first track for 5 secondtPlay of last track for 5 secondtPlay of first track for 5 secondtDisc unchucking Setting Method: 1. After setting the test mode, rotate the [l AMS L] dial to select �94. SET AGING� and press the [l AMS L] dial to enter. 2. When �AGING TIMES� is displayed, rotate the [l AMS L] dial to set the number of aging times. (For the number of times, every 10 times can be set. Setting 0 (zero) eliminates the count limitation where the aging is repeated until an error occurs)
Note: Do not perform unmanned overnight aging.
4-6. SHIPPING MODE The repaired set must be initialized, and for this purpose the set should be set to the shipping mode. Setting Method: 1. After setting the test mode, rotate the [l AMS L] dial to select �8d Set Up Init� and press the [l AMS L] dial to enter. 2. �8D 000000000 00� will be displayed, and if the scroll starts in the left direction, the set initialization has completed 3. Press the [POWER] button to turn the power off.
Note: Take care not to leave the test disc in the set.
The following setups are established in the SHIPPING MODE 1. Initialization of EEPROM (IC903) � PLAY MODE ALL DISCS, CONTINUE � COMMAND MODE CD1 � LAYER SELECTSACD � M/2CH SELECT MULTI � DIGITAL FILTER STD � 2ch SPK MODE 2ch DIRECT � Mch SPK MODEMch DIRECT � Resetting the accumulated hours meter. 2. Chucking at the DISC1 position.
3. Press the [l AMS L] dial, and �AGING START� will be displayed instantaneously, then �DISC IN & JOG ON� will be displayed and the tray will come out automatically. 4. Place a disc (CD or the SACD SL disc) on the tray, and press the [l AMS L] dial to start the aging. 5. At the completion of aging by the set number of times, the tray will come out automatically and the check will stop. Typical time required for aging About 1 hour/100 times �AGING SUCCESS!� will be displayed if no error occurred in the aging, or the error will be displayed if an error occurred. (Refer to the following error list)
Error List An error occurring during the check in the aging mode of the test mode is displayed automatically (scroll display) immediately when the error occurred. < How to view the error history > 1. Select �95 DISP ERROR� with the [l AMS L] key, and press the [l AMS L] key once. 2. The error that has occurred lastly in the set and the signal status (H = 1, L = 0) at that time are displayed on the FL display by scrolling. (Types of the errors and the signal status that can be checked, are the same as the error display of the aging mode.) 3. Press the [l AMS L] key once again to show the error history repeatedly. 4. When the error history is displayed with scrolling once, the mode returns to the normal test mode.
22
|
|
|
> |
|
