|
|
|
Kto jest w sklepie?
Sklep przegląda 6043 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
PURITY CONVERGENCE ADJUSTMENT
No. Adjusment point Conditions/Adjusting procedure Waveform or others
PURITY ADJ. GREEN-ONLY Adjust 1 CONVERGENC 1. Receive the "Crosshatch Pattern" signal.
beam current to ~ 500 µA. ADJ. 2. Using the remote controller, call NORMAL mode. BGR
2. Maintain purity magnet at the zero magnetic ( To be done
a b B field and keep static convergence roughly after the purity STATIC CONVERGENCE
ours. through microscope. Adjust landing to the 2. Turn the 6-pole magnet to proper opening anA rank requirements. Fig. a
3. Observe points a, b, as shown Fig. 1-1 gle in order to superpose the blue and red col-
adjusted. adjustment.) 1. Turn the 4-pole magnet to a proper opening anG R
RGB 4. Orient raster rotation 0 eastward. gle in order to superpose the green colour over 5. Tighten up deflection coil screws. the blue and red colours.
Fig. 1-1
6. Make sure CRT corners landing meet the A DYNAMIC CONVERGENCE G
» Tightening torque: 108 20 N (11 ± 2 kgf) R
rank requirements. If not, stick magnet sheet 1. Adjust convergence on fringes of the B to correct it. screen in the following steps. A Note: This adjustment must be done after a) Fig. a: Drive the wedge at point "a" and swing
deflection coil upward. warming up the unit for 30 minutes or and swing the deflection coil downward. G
Fig. b
longer with a beam current over 500 µA. b) Fig. b: Drive the wedge at points "b" and "c" R G B B A = B the deflection coil rightward.
d) Fig. d: Drive the "b" wedge deeper and swing c) Fig. c: Drive the "c" wedge deeper and swing R
Fig. 1-2 the deflection coil leftward. Rank "A"
R
Fig. c 2. Fix all wedges on the CRT and apply glass tape over them. (On right of the CRT) BGR magnet unit (purity, 4-pole, 6-pole magnets) and B magnet unit lock screw. 3. Apply lacquer to the deflection yoke lock screw, G
7
A Finally received the Red-only and Blue-only sigB Wedge "a" A = B Fig. 1-3 Lacquer Rank "A" (On left of the CRT)
nals to make sure there is no other colours on the Fig. d screen.
About 100 Deg
Wedge "c" "b"
4-pole magnet 6-pole magnet CRT neck
(21") 20cm Lacquer
Purity magnet 40cm(14")
14U10/15 14U20/25
7-1 7-2
|
|
|
> |
|
